Search results

Materials for the FDM process can be produced from customised blends or from commercially available resins.
Most of the research in this area describes the behaviour of the ABS and compares this material with other materials.
International Journal of Manufacturing Engineering (2014)
Materials 8 (2015) 5834-46
Advances in Science and Technology Research Journal 9 (2015)12-19.

Lichtenberg, Principles of Plasma Discharges and Materials Processing, 2nd ed., Wiley-Interscience, Hoboken, 2005
Dusane, Materials Letters 60 (2006) 2915–2919
[10] H, Zhang, Z, Xu, Optical Materials 20 (2002) 177-181
Renault, G, Passemard, Materials Science in Semiconductor Processing 7 (2004) 301-305
Nickel, Materials Science and Engineering B 159-160 (2009) 355-360

Investigation of Static and Dynamic Response of graphite and carbon fiber modified conductive asphalt-based composite Ning LI 1, a, Shaopeng WU 2, b, Conghui LIU 3, c, 1 Key Laboratory of Silicate Materials Science and Engineering (Wuhan University of Technology), Ministry of Education, Wuhan 430070, China 2 Key Laboratory of Silicate Materials Science and Engineering (Wuhan University of Technology), Ministry of Education, Wuhan 430070, China 3 Key Laboratory of Silicate Materials Science and Engineering (Wuhan University of Technology), Ministry of Education, Wuhan 430070, China a lin@whut.edu.cn, bwusp@whut.edu.cn, cchlaw@whut.edu.cn Keywords: conductive asphalt-based composite, indirect tensile strength, fatigue property.
Conductive materials percentages may have influences on performance of asphalt mixture.
Experimental Materials.
It is illustrated that asphalt materials exhibited high stress resistance in high loading speed.
When applied a high stress, conductive asphalt materials seem perform better fatigue properties.

In liver tissue scaffold fabrication, indirect casting techniques can be use for a much wider range of materials.
With regards to the manufacturing of implant, the medical models obtained by RP are normally used indirectly, as masters, to produce prosthesis in biocompatible conventional materials (e.g.
Scaffolds are made from biodegradable materials, which can degrade slowly in the body, leaving only the new regenerated tissues [11].
Any of rapid prototyping process can be use to directly fabricated a bio-compatible materials such as hydroxyapatite (HA), poly-lactide-co-glycolide (PLGA) etc.
Wilson et al.: Journal of Biomedical and Material Research, Vol.68, (2004) p.123-132

Estimation of Local Plastic Deformation in Cutting Zone during Turning Maroš Martinkovič1, a *and Peter Pokorný1,b 1Slovak University of Technology in Bratislava Faculty of Materials Science and Technology in Trnava, Paulinska 16 917 24 Trnava, Slovak Republic amaros.martinkovic@stuba.sk, bpeter.pokorny@stuba.sk Keywords: deformation, turning, cutting zone Abstract.
Difference between these two angels 18° means that the material has middle plasticity (the difference is from 0 for ductile materials to 30 for brittle materials).
Dolinsek, Work-hardening in the drilling of austenitic stainless steels, Journal of Material Processing Technology 63 (2003) 63 - 70
Vaclav, Estimation of grain deformation of polycrystalline materials, Advanced Science, Engineering and Medicine 5 (2013) 585 - 588
Vaclav, Estimation of local plastic deformation of polycrystalline materials, Key Engineering Materials 586 (2014) 39 - 42.

The study of stability of time-delay systems in Milling Xiaoguang Zhang1, a, Qiuping Ren2,b and Hong Du3,c 1 Science College ,Heilongjiang University of Science & Technology, harbin, China,150022 2 Science College ,Heilongjiang University of Science & Technology, harbin, China 3 Science College ,Heilongjiang University of Science & Technology, harbin, China asalary1357@163.com, bguanghuiwang8668@163.com, c sea_163126@126.com Keywords: milling .
Introduction With the continuous development of science and technology, people from all fields continuously put forward a lot of delay differential equations .
Milling has a relatively low cutting force in machining process, to ensure high machining accuracy and can obtain the advantage of high material removal rate, and therefore is widely applied in aviation, aerospace, shipbuilding, mould and auto manufacturing complicated parts[2-3].
Acknowledgements This work was financially supported by Scientifc Research Fund of Heilongjiang Provincial Education Department (NO : 12541728) References: [1] Stepan G,Szalai R,Mann B P,et al.Nonlinear Dynamics of High-speed Milling-analyses, Numerics,and Experiments[J].ASME Journal of Vibration and Acoustics,2005,127(2):197-203
[3] Elbeyli O,Sun J Q.On the Semi-discretization Method for Feed Back Control Design of Linear Systems with Time Delay[J].Journal of Sound and Vibration,2004,273(1/2):429-440

Introduction In the 1970s, academicians from the United States Virginia Polytechnic Institute and State University, like Claus, embedded optic fiber in carbon fiber for reinforce composite materials, perceiving stress and fracture-damage, called for adaptive material at that time.
Journal of University of Electronic Science and Technology of China, 2011(05)
Science & Technology Information, 2011(28)
Journal of Zhejiang University of Technology. 2011(06)
Chinese Journal of Sensors and Actuators. 2011(02) [8] Chang Fei.  

The bonnet’s parameters are the same as mentioned above and this paper chooses BK7 as the plane wafer for the reason that it is the most commonly used material in our practical polishing process.
Acknowledgements This work was supported by the National Key S&T Special Projects (No. 2011ZX04004-061) and the Natural Science Foundation of China (No. 51075343).
Xie, et al: Journal of Huazhong University of Science and Technology (Nature Science Edition) 35:104-107. (2007)
Xie, et al: Chinese Journal of Mechanical Engineering, 21, pp. 29-33. (2008)
Jin: Journal of Mechanical Engineering 45:308-312. (2009)

The test results are considered to be able to assure conformability of the tests, validate the stress equilibrium assumption, and show that the stress versus strain curves of foamed ceramic composite display strain hardening effect and damage softening effect as brittle materials.
Thus, it is thought that the dynamic compressive response of foamed ceramic composite shows apparent differences from other foamed materials such as porous metal and poly foam, whose dynamic response show three distinct regions: an elastic region, a collapse region (nearly a platform) and a densification region [5].
Acknowledgements This work was financially supported by the China Postdoctoral Science Foundation (20100480685), China Postdoctoral Science Foundation (2011M501394).
National Science Foundation of China (50802092), and National Science Foundation of China (11202206).
Fleck, High strain rate compressive behavior of aluminium alloy foams [J], International Journal of Impact Engineering. 24 (2000) 277- 298

International Materials Reviews. 47 (2002) 49-85
Atkinson, Semisolid processing of metallic materials.
Materials Science and Technology. 26 (2010) 1401-1413
Chakraborty, Development of an efficient grain refiner for Al–7Si alloy, Materials Science and Engineering: A 280 (2000) 58–61
Schmid-Fetzer, Thermodynamic aspects of grain refinement of Al–Si alloys using Ti and B, Materials Science and Engineering: A 395 (2005) 10–21