Search results

According to the mechanical properties, these materials are capable of being used as insulating material for both semi-load bearing and insulating elements [7].
Australian J. of Basic & Applied Sciences, 5 (2011): 1727-1733 [3] H.G.
Journal of Construction and Building Materials, 26 (2012): 638-654 [6] M.A.
Huang, Pore Structure Properties of Materials, Fu-Han, Taiwan, 1980, pp. 34-43
Journal of Construction & Building Materials, 25 (2011): 705-716

Because of the higher enthalpy emitted and smaller volume change experienced in the course of phase change, NPG (Neopentylglycol) and some of its derivatives have been considered as more excellent heat storage materials than paraffin et.al., which can storage energy when changes from liquid phase to solid phase.
Experiments preparations of the samples Put NPG, TRIS, PE(chemically pure materials) into drying machine to desiccate serial hours.
Small thermal conductivity is not favorable to the application of heat storage materials.
Acknowledges This work was financially supported by National Natural Science Foundation of China （21106048）the Fundamental Research Funds for the Central Universities, SCUT (X2LXD2104550) References [1] L.
Thermodynamics.38 (2006) 1312-1326 [10] Lu D,Jiang P, Xu ZH ZH: Solid Physics (ShangHai Science Press, ShangHai2003)

., Guangzhou 510642, China； 2Guangdong Baiyun University,Guangzhou 510450 China； 3Zhongshan College, Univ. of Electronic Science and Technology of China, Zhongshan 528402, China； amxz2004350118@163.com, b lichyx@scau.edu.cn, c zhanglili8866@163.com, d 35187700@qq.com Keywords: Maize; Deep-bed drying; Drying Characteristics Abstract.
Experimental Equipment and Material Experimental equipment (Fig1) was consisted of orifice flux-meter, adjustable centrifugal blower (DF-3, Rated Power 250 W, rotational speed 2800r/min, total pressure 860Pa, flow rate 5.05 m3/min), U-Tube and drying tower.
U-Tube 4.drying tower 5.maize Fig.1 Experimental Equipment The testing material (JIDAN 46) was from the forth Grain Depot of Suihua City Heilongjiang Province.
References [1] Li Changyou, Shao Yaojian, Kamide Junichi（1996）, Measuring the drying characteristics of wheat in a deep-bed from continuous drying air dynamics, journal of south China agricultural university,17(1), 102-107.
Journal of south China agricultural university, 1998, vol.3.

Conductivity coefficient a = k/cρ, ρ is the density and k is the shock factor. 2.2 Shock stressing formula Strain generated by expansion shock when elastomeric shock of isotropic material changes is (2) Building structure is an elastic body, due to boundary constraints and constraints between the various parts of the body, shock stressing occurs.
Journal of the Aeronautical Science, 1956, 23(2): 179-181
Aerospace Science and Technology, 2013
Journal of sound and vibration, 2003, 262(4): 865-876
International Journal of Mechanical Sciences, 2011, 53(9): 734-743

Fig. 2 Cross section of the driving mechanism The material object of this mechanism is shown in fig. 3.
BK2011002 and the National Natural Science Foundation of China under Grants No. 41106084.
Journal of Atmospheric and Oceanic Technology, 16(1999.)1816-1829
International Journal of Offshore and Polar Engineering.14(2004)176–183
Journal of Marine Systems, 77 (2009)397-408

It was designed to prevent the filter materials from mixing with each other and ease to remove for some maintenance work.
At afternoon, house occupants performs the food preparation activities which involved washing raw materials such as fish, chicken and so on which is done in the kitchen sink which pose microbial contamination if discharge directly to drains.
Kassim, Application of Peat Filter Media in Treating Kitchen Wastewater, International Journal of Zero Waste Generation 1, 1 (2013) 11-16
Gross, Greywater reuse for irrigation: Effect on soil propertiesm, Science of the Total Environment, 408(12) (2010) 2501-2508
Son, Quantification of Escherichia coli O157: H7 in organic vegetables and chickens, International Food Research Journal 20(2) (2013) 1023-1029

Model of Material Removal Mechanism and Design of Wheel Model of Material Removal Mechanism.
Acknowledgements National Natural Science Foundation of China (NSFC) (Grant No. 50675029), Joint Fund of NSFC with Guangdong (Grant No.
Jin: Chinese Journal of Mechanical Engineering, Vol. 39 (2003) No.10, pp.100-105.
Cook: Journal of Non-crystalline Solids, Vol. 120 (1990) No.1-3, pp.152-171
Susa: Journal of Non-Crystalline Solids, Vol. 283 (2001) No.1-3, pp.129-136

According to the preliminary design materials, design floor elevation is 80 meter, two high slopes on both sides will form in the north and the south, the north slope length is about 380 m, The highest grade is about 55 m.
(Natural Sciences), 2007(6):528-532
Journal of Zhejiang University ( Engineering Science), 2006(3):494-500
Journal of Liaoning Technical University（Natural Science）,2010(1):99-102
Journal of Hunan University(Natural Sciences),2011(5):19-23

There are several approaches for micro fabrication such as etching, electron beam, excimer laser and micro mechanical machining, but these processes are expensive, harmful to health and unable to fabricate the materials which are difficult to break metallic bonds.
The beam is made of composite materials composed of multiple visco-elastic layers and constrained layers.
Chang, Development of a Prototype Micro-wire-EDM Machine, Journal of Materials Processing Technology, Vol. 149 (2004 ) pp. 99-105 [9] C.
Chen, Development of a Novel Micro Wire-EDM Mechanism for the Fabricating of Micro Parts, Materials Science Forum, Vols. 505-507 (2006), pp. 235-240 [10] S.
Du, Study of an Ultrafine W-EDM Technique, Journal of Micromechanics and Microengineering, Vol. 19 (2009), pp. 1-8

Pipe materials such as resin and PVC are pipe materials cut by hand.
However, few studies on cutting pipe-shaped material have been reported.
It was found that the cutting edge of the tool fractures the pipe material.
Nakagawa, T Miura:Study on Cutting by a Knife-edged Cutter (2nd Report): Simulation on Separation of Cutting Material Using FEM, Journal of Japan Society for Precision Engineering, Vol.63, No.1(1997), pp.70-75
Kailas: Effect of directionality of unidirectional grinding marks on friction and transfer layer formation of Mg on steel using inclined scratch test, Materials Science and Engineering A, 429 (2006), pp.149–160.