Search results

They are widely applied as structural and dielectric materials in the microelectronics, electrical and aerospace industries [3-6].
The substrates were spin-coated with a patterned layer of thick AZ4620 photoresist (AZ Electronic Materials).
Ha, Advanced Materials for Optics and Electronics, Vol. 10, Iss. 6, pp. 273-283 (2000)
Rodbell, Annual Review of Materials Research 30, pp. 229-262 (2000)
Feng, Journal of Vacuum Science and Technology.

Rolatube Ltd., a small UK company, have patented a method of forming a bistable structure in this way using composite materials.
Proceedings of the Royal Society A: Mathematical, Physical & Engineering Sciences 455(1983) pp.1003-1048 [2] S.D.
Proceedings of the Royal Society A: Mathematical, Physical & Engineering Sciences 462(2067) pp. 839-854
International Journal of Solids and Structures 41(11-12) pp. 2801-2820
To be published in the Proceedings of the Royal Society A: Mathematical, Physical & Engineering Sciences

The massive material molecules generated and metal particles within the engine got together then formed resin glue film which attached to the surface of parts.
* Fund project: the project of national natural science funds（51375278） References [1] Diaby M, Sablier M, Le Negrate A, et al.
Shoemaker, “Molten salt process”, Wire Journal, vol. 4, pp. 33-38, Mar. 1971
Journal of Cleaner Production, 2014,68(0):243-251
Solar Energy Materials, 1990, 21(1): 51-60.

Bakar 3,e 1Department of Mechanical & Materials Engineering, Faculty of Engineering & Built Environment, Universiti Kebangsaan Malaysia, Malaysia 2Institute of Space Science, Universiti Kebangsaan Malaysia 3 Engineering Division, Perusahaan Otomobil Nasional Sdn.
The failure due to cracks usually initial from the fillet region and propagates along the journal to the oilseal.
Based from the experimental analysis the failure time occurs are very random between the operating hours due to the load applied and the material properties of the crankshaft.
Torsion acting on the crankshaft was derived through Eq. 6 whereby and T is the torque that is applied by the connecting rod to the crankpin web that is acting on the main journal of the crankshaft as shown in Fig. 6 .
Side view illustration of applied load on the main journal

., 03142, Kyiv, Ukraine 2Institute of Physics of Materials, Academy of Sciences of Czech Republic, 22, Zizkova, Brno *walduk@bigmir.net Keywords: local stress, fracture, cleavage, embrittlement, strength Abstract.
In approximation of two-parameter Weibull distribution the Weibull stress may be expressed as: (1) where denotes the highly-stressed volume of material just ahead of the crack tip within which the triggering event of cleavage fracture occurs, m is the Weibull modulus, V0 – is the reference volume.
Rice: Journal Mech. and Physics Solids, Vol. 21 (1973), p. 395 [2] F.M.
Pineau: International Journal of fracture, Vol. 138 (2006), p. 139
Kotrechko: Journal of Theoretical and Applied Mechanics, Vol. 51 (2013), p. 75.

Motivated by these applications, open and closed-cell metal foams of different densities, cell sizes, and materials have been studied [1].
Selection of constituent materials is an important part of designing syntactic foams, where strength, modulus as well as density can be optimized [4].
Calculation Model The Al alloy/SiChs composite materials are prepared by a pressure infiltration method.
Fig.1 (a) shows a typical representative section recorded of the composite materials [6].
Fang, FEM for brake discs of SiC 3D continuous ceramic reinforced 7075 aluminum alloy for CRH3 trains applying emergency braking, Applied Mechanics and Materials. 120 (2012) 51-55

The QM-RM allows the direct determination of the QSPF in advanced materials at instantaneous thermo-mechanical material working conditions.
[5] Juan Daniel Muñoz-Andrade, “Unification of Physics during Super Plastic Flow in Advanced Materials”, Materials Science Forum (2016), ISSN: 1662-9752, Vols. 838-839, 78-83
Prasad, “Hot working of commercial Ti-6Al-4V with an equiaxed a+b microstructure: materials modeling consideration”, Materials Science and Engineering A284 (20009 184-194
Sanders, Bin Liu, Weidong Zhang, Canzu Zhou, Develoment of grian size titanium 6Al-4V sheet material for low temperaure superplastic forming, Materials Science & Engineering A 608 (2014) 265-272
Miracle, “Superplastic behavior of Ti-6Al-4V-0.1 alloy”, Materials Science and Engineering A 539 (2012) 7-12.

Test materials and specimens preparation Test materials The materials used were ordinary Portland cement P.O 42.5 produced by Rizhao ZhongLian cement plant, the compressive strength at 28 days of which is 46.8 MPa, and well-graded granite gravel produced in Chentuan, with the size from 5 mm to 31.5 mm, the needle-like particles of 5.3%, the crushing index of 6.8%, the mud content of 0.4% and the apparent density of 2620 kg/m3.The river sand was produced in Chentuan, with the fineness modulus of 2.9, the mud content of 1.8% and the apparent density of 2620 kg/m3.
The air entraining agent is produced by Qingdao Keli building material company.
So it is good to increase the continuity of material and improve the uniformity of concrete.
(China Science Press, China 2003).
SHPB Test Study on Dynamic Characteristics of Polypropylene Fiber Concrete, Journal of PLA University of Science and Technology (Natural Science Edition), 6(4), (2005), pp.351-354.

Composite materials can be made from a variety of materials, including palm fibre, which has excellent modulus of elasticity and tensile strength.
New materials have been created using flax, glass, and unsaturated polyester resin.
The growth of composite science can rely on this material since it produces good mechanical strength, notably neat glass/polyester laminate.
Reinforcing composite materials with date palm fibre has a number of advantages.
[5] Biruk Gedif Worku, Tessera Alemneh Wubieneh, "Mechanical Properties of Composite Materials from Waste Poly(ethylene terephthalate) Reinforced with Glass Fibers and Waste Window Glass", International Journal of Polymer Science, vol. 2021, Article ID 3320226, 14 pages, 2021. https://doi.org/10.1155/2021/3320226 [6] P.

Conductive filaments are 8 roots for the warp and weft conductive material.
Experimental Choice of Materials.Terylene yarn is chosen as the insulating material.
The stainless steel filaments are selected as the conductive material.
Russo, et al: Journal of IBM.
Ding: Journal of Donghua University(natural science) Vol. 35(2009), p.161-166