Search results

Soboyejo1,6 1Department of Materials Science and Engineering, African University of Science and Technology, Km 10 Airport Road, Abuja 2Department of Materials Science and Engineering, University of Ghana, Legon-Accra, Ghana 3Institute for Advanced Materials, Devices and Nanotechnology.
Department of Materials Science and Engineering, Rutgers University, New Jersey, USA. 4Department of Theoretical and Applied Physics, African University of University of Science and Technology, Km 10 Airport Road, Abuja 5Physics Advanced Laboratory, Sheda Science and Technology Complex, Abuja 6Princeton Institute of Science and Technology of Materials, Department of Mechanical and Aerospace Engineering, Princeton University, New Jersey, USA Keywords: Organic Solar Cell; Interfacial layer; Adhesion; Pressure; Charge Transport Abstract This paper explored the effects of pressure on contacts between layers of organic photovoltaic cells with poly (3-hexylthiophene):phenyl-C61-butyric acid methyl ester (P3HT:PCBM) as the active layer.
Soboyejo, Mechanical Properties of Engineered Materials (CRC, New York, 2003)
Callister, Materials Science and Engineering: An Introduction (Wiley, New York, 2003)
Dalton, Introduction to Organic Electronic and Optoelectronic Materials and Devices (Optical Science and Engineering) 1st Edition, pp CRC, Press, 2008

Grugel, Secondary and tertiary dendrite arm spacing relationships in directionally solidified Al-Si alloys, Journal of Material Science 28 (1993) 677-683
Samuel, Effect of alloying elements and dendrite arm spacing on the microstructure and hardness of an AI-Si-Cu-Mg-Fe-Mn (380) aluminium die-casting alloy, Journal of Materials Science 30 (1995) 1698-1708
Shabestari, The effect of iron and manganese on the formation of intermetallic compounds in aluminum–silicon alloys, Materials Science and Engineering A 383 (2004) 289–298
Luc, Eutectic modification and microstructure development in Al–Si Alloys, Materials Science and Engineering A 413-414 (2005) 243-248
%SiC Composites, Materials Transactions 49 (2008) 671-680.

Grivickas2 1 Department of Electronics, Tallinn Technical University, Ehitajate tee 5, 19086 Tallinn, Estonia, 2 Institute of Materials Science and Applied Research, Vilnius University, Sauletekio 10, LT-2054 Vilnius, Lithuania Keywords: Silicon Carbide, Germanium, Silicon, Phonon Drag, Seebeck Coefficient, Thermoelectric Figure-of-Merit Abstract.
The µ meff -term explains also the close Sph values for p- and n-type materials (see Ge and Si data in Fig.1).
Promising examples of special effective materials [10,11] are compared with best-case estimations for p-6H-SiC at different free carrier concentrations.
The Estonian Science Foundation (grant 5180) and the Lithuanian Science and Studies Foundation are acknowledged for financial support.
Journal Vol. 27(3) (1964), p.43

Materials and Experimental Programme Materials Used.
Key Engineering Materials 803: (2019) 216–221
Iranian Journal of Science and Technology, Transactions of Civil Engineering, (2021) https://doi.org/10.1007/s40996-021-00588-w
Journal of Materials Science, vol. 34, no. 15, (1999) pp. 3737–3745
Construction and Building Materials, 142 (2017) 101–108

PPA (Purchase and Procurement Agent): The required purchases for raw materials necessary tools and etc. are managed by this agent.
RTSA (Return to Supplier Agent): If the return of the purchased raw materials is needed, this agent sends a request of return to RFCA and pursues the process to do this.
- OFA, COA and SLCA managed the operation of the supply chain and due to this close relation and adequate information flow, the rejection and returning of the sold or bought goods and materials were decreased
- Decreased transportation cost: the company planned to choose the best supplier in quality and cost and also due to decrease of the returned materials and goods, the transportation cost was reduced
Hebbal, Multi Agent System Model of Supply Chain for Information Sharing, Contemporary Engineering Sciences. 3(1) (2010) 1-16

These tests are compared with polymeric materials without added nanofiller.
Material and Experimental Material.
The tip has a cone shape, type D for harder type of materials.
Composites science and technology 69, (2009), pp. 1756-1763
European Polymer Journal 43, (2007), pp. 3750-3756

Roll bonding is a joining-by-forming process to permanently join two or more layers of different materials by hot or cold rolling.
Introduction Roll bonding is a widely applied industrial process to permanently combine two or more layers of different materials by hot or cold rolling.
The materials for the top- and base-layer are AA4xxx and AA3xxx, respectively.
Hirt, A New FE-Model for the Investigation of Bond Formation and Failure in Roll Bonding Process, Material Science Forum 854, 2016, 152-157 [8] C.
Allwood, The influence of deformation conditions in solid-state aluminium welding processes on the resulting weld strength, Journal of Materials Processing Technology 214 (2014) 2576–2592 [10] Information on http://abaqus.software.polimi.it/v6.14/books/usb/default.htm [11] R.

Flume: Flumes are generally made from non-conductive and non-hygroscopic materials.
Journal of Building Materials. 2009, 12(1): 112-115
Journal of Huazhong University of Science and Technology(Urban Science Edition), 2008, 25(2): 19-22
Contactless, transformer-based measurement of the resistivity of materials [P].
ACI Materials Journal, 2001, 98(1): 25-35

Piccioni, Seismic Response of a Historic Masonry Construction Isolated by Stable Unbonded Fiber-Reinforced Elastomeric Isolators (SU-FREI), Key Engineering Materials (2014)
Construction and Building Materials, 21(2007), 1311–1321
Diaferio, Dynamic analysis of a historical fortified tower, Key Engineering Materials (2014) [16] T.
Lourenço, Non-destructive tests for the structural assessment of a historical bridge over the Tua River, Key Engineering Materials 569-570 (2013) 390-397 [21] A.
Piccioni, Mechanical characterization of Apricena marble by ultrasonic immersion tests, Key Engineering Materials (2014)

Experimental Procedures Materials and feedstock preparation.
Acknowledgments The authors acknowledge financial support from the Natural Sciences and Engineering Research Council of Canada (NSERC) under grant no.
Martin, Effect of binder jetting microstructure variability on low cycle fatigue behavior of 316L, Materials Science and Engineering: A 839 (2022) 142820. https://doi.org/10.1016/j.msea.2022.142820
Vieira, Influence of metallic powder characteristics on extruded feedstock performance for indirect additive manufacturing, Materials 14 (2021). https://doi.org/10.3390/ma14237136
Pasebani, A review on binder jet additive manufacturing of 316L stainless steel, Journal of Manufacturing and Materials Processing 3 (2019) 8–12. https://doi.org/10.3390/jmmp3030082