Search results

In order to obtain the optimal molecular structure for the electronic structure calculation, we performed a geometry optimization of an individual molecule of the polymer at AM1 level and then extracted the geometry of the molecule.
The AM1 program was implemented in the MOPAC package (Quantum Chemistry Program Exchange, Indiana University, USA).
The details on the electronic structure calculations were described in literature [5-7].
From the viewpoint of molecular structure, the conjugated polymer is a rigid planar structure.
Left panel: molecular structure of the conjugated polymer poly(cyclopenta-1,3-diene).

Real crystals often have a mosaic structure.
The first term is structure independent and the last two terms are dependent on the crystal structure.
Mann, Journal of Physics and Chemistry of Solids, 12 (1960) 326
Lannoo, Journal of Physics and Chemistry of Solids, 37 (1976) 699
Hall, Journal of Physics and Chemistry of Solids, 3 (1957) 210

Stress analysis was done to explain about the effective stress influenced on polymer structure.
The research methodology process is recommended for design and analysis of polymer structure.
And special thanks for Head of mechanical and structure Laboratory.
Rubber Chemistry and Technology, 1993. 66(5): p. 754-771
Rubber Chemistry and Technology, 1994. 67(3): p. 481-503

From equation (1) follows: (3) and replacing this in equation (2): (4) Neglecting terms of order 2 and 3, which are very small, we have: (5) The injected piece contraction depends on the following factors: - structure of macromolecular material used in injection; - the form of the injected part, in particular wall thickness, variations of the wall thickness of the work piece which influence the cooling conditions and time cooling differences between the two areas of the part; - cooling conditions in the mould, interpreted as tiles mould temperature uniformity and heat removal rate from the mould; The injection parameters of the process are: - melt
Macromolecular chemistry presents, in a temperature range of 0° C to 300° C, linear variations in the volume of melts up to the freezing temperature, of the variation exponential variation between the freezing and the flow temperature and a linear variation after the flow point for the amorphous polymers or that of the change of state for the crystalline ones.
McCleverty, Nonlinear Optical Properties of Metal Complexes,Comprehensive Coordination Chemistry, Pergamon Press, Oxford, U.K., Vol. 5 (1987)
Pomeranz, Wheat Chemistry and Technology, Minnesota, (1971)

(6) (7) Atomic and molecular weights of all substances related in stoichiometry of hydration and pozzolanic reactions could be obtained from any standard textbook of chemistry.
It was concluded that C-S-H from pozzolanic reactions had the same structure as C-S-H from hydration of cement [4].
Taylor, Cement Chemistry, 2nd Ed., Thomas Telford Publishing, Thomas Telford Services, Ltd, London, 1997
Bogue, Chemistry of Portland cement, Reinhold, New York, 1955

School of Chemistry and Chemical Engineering.
Fig.1 Chemical structure of Mn(Ⅲ)DP 2.
Frank, Metal‐Free Heterogeneous Catalysis for Sustainable Chemistry, J.
Relativistic Effects in Chemistry: More Common Than You Thought, J.

In short, the molecularly imprinted polymer is prepared by mixing the template molecule with functional monomers, cross-linked under certain conditions and extracted out the template molecule[1]. molecular imprinting has become increasingly attractive in many fields of chemistry and biology, particularly as solid phase extraction, enzyme-mimicking catalyzer, chemical-bionic sensor, packing material, biological material simulation [2-4] etc.
From the two sections, the pore structure was basically same, but we could clearly observe a layer covered on the surface of the membrane.
Progress in chemistry, Vol. 20 (2008):P. 960
Analytical and Bioanalytical Chemistry, Vol.67 (1995) P. 2142

Lonic Liquid [Bmim]OH Grafted Catalyst for Cycloaddition of Carbon Dioxide Xuelan Zhang1, a, Dengfeng Wang1,b 1College of Chemistry, Chemical Engineering and Materials Science, Zaozhuang University, Zaozhuang, 277160, P.R.
Introduction In recent times room temperature ionic liquids have attracted increasing interest in the area of green chemistry [1].
Such grafted ionic liquids possessed good thermal stability and mesoporous structure.
Hölderich: Green Chemistry Vol. 4 (2002), p. 88 [19] S.

In our work, Di-n-octyl-o-phthalate (Tianjin Chemistry Reagent factory, China) and 2,5-Frandione (Chengdu Kelong Chemistry and Industry, China) were chose as plasticizer and compatibilizer, respectively.
Fig. 3 SEM of lignosulfonate-polystyrene blend (×5000) 3.2 SEM of blends Fig 3 showed the SEM photographs of blend surface morphologic structure and the following information could be obtained.
Liang, Chemistry and Agglutinate, 2(2003) pp. 2456

The mechanical properties of modified attapulgite reinforced nature rubber and styrene-butadiene rubber nanocomposites Jihu Wanga, Hongbo Liub, Shaoguo Wenc, Yan Shend College of Chemistry and Chemical engineering, Shanghai University of Engineering Science, Shanghai 201620, China awangjihu@126.com, bliuhongbo81@gmail.com,csgwen@yahoo.cn,dsimpleseaon@hotmail.com Keywords: attapulgite natural rubber styrene-butadiene rubber nanocomposites Abstract.
The band at 3419 cm-1 was associated with water hydroxyl stretching in the attapulgite structure.
Chen: Journal of Physics and Chemistry of Solids Vol. 69 (2008), p.1411 [7]Z.Q.
Jiang: Journal of Solid State Chemistry Vol.182 (2009), p.2130 [8]J.H.