Search results

Journal of Hazardous Materials 180,115-121
Journal of Hazardous Mat erials182, 656-664
Microchemical Journal 94, 99-107
Journal of Hazardous Materials 143, 511-515
Science of the Total Environment 408, 726-733

The study on tail-water treatment model in Shandong Province Ren Jiaguo, Wu Qianqian Shandong Provincial Key Laboratory of Depositional Mineralization & Sedimentary Minerals, College of Geological Sciences & Engineering, Shandong University of Science and Technology Qingdao 266590 renjiaguo2008@126.com Keywords: Geothermal tail water; Treatment model; Combined Process Abstract.
(2)Salt(sodium chloride), magnesium, potassium and bromine in the dense water are basic raw materials and important products in China’s chemical industry, the dense water generated in the treatment process which has high salt content, up to 30g/L or more, close to the brine’s, has a potential of exploitation.
Iron and Manganese Removal Process Research in Geothermal Water[J], Environmental Sciences, 2001,27:21-22
Journal of Ocean University of China, 5(4):357-362
Advanced Materials Research, 201-203: 2540-2543

Applied Surface Science, 334, 151–156
Luminescence Studies on the europium doped strontium metasilicate phosphor prepared by solid state reaction method Journal of Science : Advanced Materials and Devices Luminescence studies on the europium doped strontium metasilicate phosphor prepared by s.
Journal of Science: Advanced Materials and Devices, 2(1), 59–68
IOP Conference Series: Materials Science and Engineering, 440(1), 1-7
Materials Chemistry and Physics, 276, 125305

In the LMM, the inertial force of a mass levitated using a pneumatic linear bearing is used as the reference force applied to the objects under test, such as force transducers, materials or structures.
Fig. 2 shows a schematic diagram of the experimental setup for evaluating the viscoelastic response of materials against impact force.
Yamaguchi, “Proposal for material viscoelasticity evaluation method under impact load”, Journal of Materials Science, Vol.40, No.18, pp.4785 – 4790, 2005
Fujii, “Microforce materials tester”, Rev.
Fujii, "Microforce materials tester based on the levitation mass method", Meas.

Experimental research was conducted in the Laboratory for materials at the Faculty of Civil Engineering, University of Belgrade.
It is the use of pozzolanic materials, such as fly ash and slag.
This research was carried out in the Laboratory for Materials, Institute for materials and structures, Faculty of Civil Engineering, University of Belgrade.
Siddique, Waste Materials and by-products in concrete, Department of Civil Engineering, Thapar University, (2008)
Savić, Achieving sustainability of concrete by recycling of solid waste materials, Mechanical Testing and Diagnosis 1 (2) (2012) 22-39

Prior to failure, ductile materials undergo significant plastic deformation, which has a major influence on damage evolution [4].
Due to their good mechanical properties and low densities, these alloys have an edge over other conventional structural materials [5].
Applied Mechanics and Materials 393, 538-543 (2013)
Najafi, “Design and manufacturing of a tele-operative rescue robot with a novel track arrangement,” Industrial Robot: An International Journal, 38(5), 476–485 (2011)
Abdullah, “Effect of Heat Treatment on Strain life of Aluminum Alloy AA 6061,” J. of Materials Science Research, 2(2), 51-59 (2013).

Warren et al. [5] showed that inclusion of phase transformation significantly affects the predicted residual stresses in ferritic materials in the area close to weld zone and not so pronounced in the area adjacent to HAZ .
"Studies on characteristics of temperature field on GTAW with a trailing heat sink for titanium sheet" Journal of Materials Processing Technology, 2004, 147, 328-355
Material Science Forum, 2006, 524-525, 479-484
Advanced Materials Research,2011, 295-297, pp 1905-1910
T., "The effect of phase transformations on predicted values of residual stresses in welded ferritic components" Materials Science Forum, 2006, 524-525, 827-832

Its nature of the particularity performance in the rock mass within the free iron oxide materials, its cementation structure make the red clay in high water content, high void ratio, high liquid plastic limit and plasticity index such as adverse environmental conditions, presents the mechanical properties of high strength and low compressibility.
Acknowledgements This work was funded by National and local joint engineering laboratory of traffic Civil Engineering Materials of Chongqing Jiao tong University (No. 
Guizhou, Guizhou science and technology press, 1991 [6]Song Yuanming Wu Weiguo, Deng Shuang.
Journal of highway engineering, 2013, 38(1):40-43
Journal of highway, 2002，(6):125-128

The material card (*MAT18) is developed using the AA3003-H18 material properties for representing the material ductility behavior.
Justus Panicker, Studies on single point incremental forming of Ti-6Al-4V alloy for aerospace applications, Materials Today: Proceedings. 22 (2020) 1967–1976
CIRP Journal of Manufacturing Science and Technology, (2017), 16, 43--54
[8] Mohanraj Murugesan, Muhammad Sajjad, and Dong Won Jung, Experimental Investigations on Incremental Sheet Forming of Commercial Aluminum Alloys for Maximum Production Quality, International Journal of Mechanical Engineering and Robotics Research, 9(9), 2020
Materials 2019, 12, 609–627

Experiment research Spiral bevel Gears closed extrusion new technology New technics process of spiral bevel Gears without fly side is as follows: eyeballing inspection of raw materials and conventional physical and chemical testing → cutting material → semi-finished product small non-oxidized heating → manufacture semi-finished product (upsetting-- punching--reaming) → coarse extrusion → precision extrusion → surface cleaning → the follow-up machining and heat treatment → test and storage .
In order to satisfy the extrusion requirements for steel-plastic, when extrusion of high-strength steel materials often choose to be above the phase transition temperature extrusion .
Compared with the open die , required extrusion distortion force reduced 50% , increase material utilization 15%, debase electric power consumption 50%, with significant economic benefits .
Journal o f Materials Processing Technology, 1995. 45(1-4) : 25-30
[3] SadeghiM H.Journal of Manufacturing Science and Engineering, 2003,125 (4) :753-762 .