Search results

Heilongjiang Science and Teclnology of Water Conservancy, 34 (3) (2006) 22-23.
Sichuan Building Materials, (3) (2006) 194-196.
Institute of Rock ＆ Soil Mechanics Chinese Academy of Sciences, (2004).
Chinese Journal of Geotechnical Engineering, 1998, 20(1):84~86.
Journal of Anhui University of Technology (Social Sciences), 2007, 24(1):38~39.

Studied materials The applied BA was collected in winter 2013 from an incineration plant situated in the Czech Republic.
Replacement was made according to the fraction distribution curves of siliceous sand and BA and bulk densities of the used materials.
Results and discussion Mechanical properties of the studied materials are described on the graphs and in the tables below.
Fig. 3 Bulk densities of the studied materials Fig. 4 Compressive strength of the studied materials (28 days) Fig. 5 Tensile strength of the studied materials (28 days) Conclusion There were crafted four mortars with increasing replacement level of siliceous sand by the MSWI bottom ash S25, S50, S75, S100 – with 25%, 50%, 75% and 100% of replaced sand.
Christensen: On-site treatment and landfilling of MSWI air pollution control residues, JOURNAL OF HAZARDOUS MATERIALS, Volume: 97 (2002) 59-70

High transversal properties requirements of heavy axial forgings, traditionally, often are met through the selection of high-performance materials, the improvement of metallurgical quality and repeated forging.
The surface material flows faster than that at the center and the material near the center is of more uniform deformation.
The numerical simulation shows that, the surface material and center material flow laterally when using SFM.
The surface material flows faster than the center material.
Liu, etc: Chinese Journal of Mechanical Engineering, Vol.19(2006), p.272.

The micro structures of the suspended materials in produced water were observed with particle imager and SEM.
Methods and Materials Materials.
Rise-3002 particle imager was used to observe the micro structures of the suspended materials in untreated produced water and treated produced water.
As shown in Fig. 1 (a), some suspended materials such as oil droplets and suspended solids in untreated produced water formed loose aggregates.
The micrographs maybe show that it is more difficult for PAC and CPAM to remove the suspended materials in the produced water.

With the continuous improvement of the requirements for light weight and high survivability of armored vehicles, the application of titanium alloy armor materials plays an extremely important role in the development of defense high-tech weapons and equipment and the promotion of national defense science and technology force [1,2].
Standard test methods for tension testing of metallic materials[S]
Metallic materials-deformation of plane-strain fracture toughness[S]
[13] GB/T 231.1-2018 Metallic materials-Brinell hardness test-Part 1: Test method[S]
[19] XQ Liu, M Zhang, SH Li, Localized Adiabatic Shear Deformation of TC4 and DT4 Alloys, Journal of Materials Science and Engineering, 2009, 27(5): 755-757, 803

We have evaluated the measurement images in many ways, and many different types of components and materials (mostly iron alloys) were analyzed.
Additionally, non-destructive measurement techniques typically do not come into direct contact with the sample, but are often limited in their application, for example, they have restrictions to predefined crystalline structures, magnetic or Raman-active materials. [2].
Materials and Methods Residual stress caused deformation is a real problem in manufacturing castings, that is why we have examined disc-type of castings as a part of our research.
Series A: Mathematical, Physical and Engineering Sciences 359.1778 (2001) 97-111
Rocha, Influence of plastic deformation over the natural frequency of steel structures, International Journal of Advanced Engineering Research and Science 7.4 (2020) 76-84

However, EPDM materials belong to organic materials, which have disadvantages of low compressive strength, high cost and poor dimensional stability, especially when used in the field of sealing device and electrical insulating materials [4].
Fig.3 shows the tensile strength of rubber composite materials results.
Zhang, et al.: Journal of Hazardous Materials,Vol. 229-230(2012), p. 251 [3] Y.
Garmabi: Materials & Design, Vol. 32(2011), p. 3803 [5] J.
Zhan, et al.: Materials Research Bulletin, Vol. 46(2011), p. 1593 [14]H.

Materials and methods Dried Perilla were purchased from drugstore (Hangzhou, China) or harvested from Hangzhou or Quzhou area, China.
Using 3# sample (Perilla leaves from Linan, Zhejiang province) as raw material, the extraction rate could be 1.71%.
Li: Journal of Agricultural and Food Chemistry.
Bates: Innovative Food Science & Emerging Technologies, Vol. 9 (2008), p. 161-169 [8] M.
Yu, Science and Technology of Food Industry: Vol. 29 (2008), 181-182 (in Chinese)

Rosin was used as raw material to prepare a rosin amide derivative.
Experimental Materials.
The raw material, gum rosin, was of industrial grade.
Journal of Oil and Gas Technology, Vol.29, No.4(2007), p.140-143
Forestry Science&Technology, Vol.32, No.1 (2007), p.59-61

It provides comprehensive classification of causes related to 4 Ms i.e. man, machine, materials and methods, and thus helps in establishing a knowledge base to deal with problems related to process/product reliability, availability and maintainability.
[2] Madu, C.N. (2005), “Strategic value of reliability and maintainability”, International Journal of Quality & Reliability Management, Vol. 22 No. 3, pp. 317-28
[3] Sharma, R. (2005), “Reduction of process defects in chrome-plated cylinder liners in WDM diesel locomotives using TQM tools”, Industrial Engineering Journal, Vol. 34 No. 3, pp. 17-21
Journal of Food Eng 2005; 69(1):79–96 [7] Connor P.D.T. (2002), Practical Reliability Engineering, Heyden, London
[9] Sharma, R., Kumar, D. and Kumar, P. (2008), Fuzzy modeling of system behavior for risk and reliability analysis, International Journal of Systems Science, 39:6, 563 – 581 [10] Chang K.H (2009) Evaluate the orderings of risk for failure problems using a more general RPN methodology, Microelectronics Reliability 49, 1586–1596