Search results

Materials Chemistry and Physics [J], 2009, 113: 515-517
Materials Review [J], 2005, 19:76-80
Journal of Alloys and Compounds [J], 2005, 389: 169-176
Materials and Design [J], 2006, 27: 405-410
Key Engineering Materials [J], 2008, 368-372:1313-1315 [11] Hao Jianjun, Ma Luping, Li Jianchang et al.

There are many and complex factors that can influence the grouting pressure, but they can be summarized in three aspects: grouting machine, grouting materials and the proprieties of strata [3].
And the grouting pressure formed by cement grout is higher than that formed by polymer chemical grout; the effects of grouting pumps, grouting materials and conditions of rock mass on the grouting pressure are the result of interaction of the three but not purely the power of grouting pumps; however, the references just qualitatively explains the factors influencing the grouting pressure and the law of grouting pressure variation, failing to draw the physical relationship between grouting pumps, grouting materials and proprieties of rock mass.
To get an ideal grouting effect in the case of grouting the same material in the rock with poor groutability, we can use the grouting pump whose flow rate is low or reduce the flow of grouting pump
Wang Dangliang “Comparison Analysis on Several Treatment Results of Mine Auxiliary Shaft Cracked Liner in Yangzhuang Mine”, Coal Science and Technology. 2009 (1), 35-38
Wang Dangliang，”Characteristics of Water Inflow and Chemical Grouting Treatment of Liu Yuanzi Coal Mine Shaft in Ordos Basin”，Journal of China University of Mining & Technology, 2010.(4)607～610

Electrospinning is an effective approach to get one-dimensional nano structured materials.
Introduction In recent years, there has been increased interest in fabrication and investigation of one-dimensional nanostructured materials, electrospinning(e-spinning) is an effective approach have received increasing attention.
Experimental Procedure Raw materials.
Science 285 (1999)1375-1377
Journal of Crystal Growth 267 (2004) 380-384.

Dynamic, Modal and Wave Propagation Analyses of 3D Functionally Graded Continua Ganesh Anandakumara and Jeong-Ho Kim b Department of Civil & Environmental Engineering, University of Connecticut, 261 Glenbrook Rd, U-2037, Storrs, CT 06269, USA a anandg@engr.uconn.edu, bjhkim@engr.uconn.edu Keywords: Functionally graded materials, Finite element methods, Dynamic analysis, Modal analysis, Rayleigh Ritz method, Wave propagation.
For the FG bar, we see that gradation affects stresses considerably more so at the fixed end than at other locations. 1 Introduction Functionally graded materials (FGMs) are a new advanced class of composites characterized by a gradual variation in composition, microstructure and material properties.
Material gradation for the beam is similar to the ones seen in Zhang and Paulino [9].
Journal of the Mechanics and Physics of Solids, 44(5):647-656, 1996
Int'l Journal of Engineering Science, 35(9):869-883, 1997

Materials cost estimation algorithm modules selects raw materials according to parts size and structure of the product preliminary design, access the relevant parameters from database and calculate raw material costs.
System Application Use C6140 ordinary lathe to process a stepped shaft, materials for 45 steel, structure size as shown in figure 1 below.
According to the structure size in figure 1 , The raw material parameter’s selection: material diameter is 63mm, length is 252mm.The calculation results of raw material cost is shown in figure 2.
References [1] Zhaohui Wang,Xiuzhuo Fu: Journal of Shandong University (Engineering Science).
[5] Yuyuan Wang,Yimin Sun,in: The operational manual of over-staff and quota(Sichuan Science and Technology Press, China 1989).

Removal of Alkali in the Red Mud Using CO2 at Ambient Conditions Xinke Wang a,Yihe Zhang*b,Fengzhu Lv c,Rongrong Lud National Laboratory of Mineral Materials, School of Materials Science and Technology, China University of Geosciences, Beijing 100083, China axinke414@163.com, bzyh@cugb.edu.cn,clfz619@ cugb.edu.cn,d79065864@163.com Keywords: Red mud, alkali content,CO2 Abstract.
Materials and Preparation 2.1 Materials Red mud used in this study was obtained from Shandong, in the form of dried-clay.
[4] Wang Qi: Journal of Environment Engineering,Vol.3(2009),p.2275
[6] Zhao Guanghui:Science and technology information,5(2000)
[8] Wang li ying:Science and technology information,7(2010)

Materials and Structures, 2007, 40: 605–613
International Journal of Solids and Structures, 1997, 34(27): 3491-3515
Applied mechanics and materials, 2012, 174-177: 3-10
Journal of Constructional Steel Research, 2009, 65(3): 523-530
Journal of Engineering Mechanics, 2003, 129(5): 548-557.

(1) (2) In the nonlinear analysis of concrete structures, the nature and characteristics of the concrete material is material inhomogeneity, and its working mechanism is characterized by the presence of micro-cracks and constitute a larger macro-cracks, resulting in concrete along with the development of structural damage.
Using ANSYS software comes with William-Warnke five-parameter failure criterion, multi- linear isotropic hardening model (M150), this failure criterion can better predict the destruction of concrete materials.
（In Chinese） [2] Yulin Wu,Jiang Xiao: New Building Materials.
（In Chinese） [6] Jinghai Zhou,Haijin He: Journal of shenyang architectural university, Natural science edition.(2010). p. 464~468.（ In Chinese） [7] Hongjiang Tong, Nonlinear analysis of reinforced concrete structures, Dalian University of Technology. (2009). p. 24~32.
（In Chinese） [8] Zongping Chen,Jinjun Xu: Journal of Building Materials. (2013). p. 24~32.（ In Chinese） [9] OIKONOMOU.N.D.

Materials and Design, 2010, 31: 1096-1104
Journal of Iron and Steel Research, 2013, 20 (7): 78-83
Materials and Design, 2012, 35: 446-456
Materials and Design, 2015, 87: 201-214
Journal of Materials Processing Tech, 2018, 262: 232-238

In addition to the Poisson's ratio, shear modulus and density of the materials properties of sleeper, the dynamic properties of sleeper should be defined in EDEM.
Huang: Applied Mechanics and Materials, Vol. 120, (2012), p. 325
Hou: Journal of Railway Engineering Society, No. 9, (2009), p. 14
Yan: Applied Mechanics and Materials, Vols. 190-191, (2012), p.369
Xu: Advanced Materials Research, Vols. 690-693, (2013), p.2726