Search results

In the milling process, material is removed from a workpiece by a rotating milling tool.
Fig.2 SLD for gyroscopic considered and not considered Acknowledgments The contents presented in this paper was supported by National Basic Research Program of China, Grant No.: 2009CB724405 and Natural Science Foundation of Shandong Province, China， Grant No.: Y2007F41.
Yi and et al.: Journal of Materials Processing Technology, Vol. 138 (2003), pp.379-384
Song and et al.: Journal of Materials Processing Technology, Vol. 209 (2009), pp.2585-2591.

Blast Damage Model An important clue to the origin of the extra dislocations is provided by the observation that plastic flow tends to occur in concentrated amounts that is, the plastic strain is not spread uniformly throughout the material, but occurs as large amounts of slip on relatively few planes.
Therefore, this generalized model is represented by: (1) where is the total shear displacement and n is the work-hardening exponent, m is a dimensionless constant depending on material properties.
Therefore, Equation (1) can be re-written as: (2) The post-yield behavior of the material is non-linear type.
Huddle: International Journal of Rock Mechanics and Mining Sciences, Vol.14 (1977), p.289
Goumans: Journal of Explosives Engineering, September-October (2004), p.6

At present, phosphor materials have been mainly prepared by a solid-state reaction technique.
The raw materials were Eu2O3 (99.99%), Ca(NO3)2·4H2O (analytical grade), 4MgCO3·Mg(OH)2·4H2O (analytical grade), ethyl silicate (analytical grade), ethanol (analytical grade), nitric acid (analytical grade) , citric acid (analytical grade), hexadecyl trimethyl ammonium bromide (CTAB) (analytical grade), and triethanolamine (analytical grade) .
Acknowledgements This work was financially supported by the Science and Technology Plan Project of Shenyang (F12-277-1-09), and the Project of the Education Department of Liaoning Province in China (L2012149).
Wang, Structure and luminescence properties of new Green-emitting phosphor BaAl12O19: Tb, Japanese Journal of Applied Physics, 46(2007) 5871-5875
Crystallization process for precursor of BaMgAl10O17:Eu prepared by sol-gel method, Journal of the Chinese Ceramic Society, 33(2005)272-278.( In Chinese) [7] Tao Y, Zhao G, Zhang W, et al.

Introduction Oxygen is an important chemical material and it has major applications in most industries.
Experimental section Material.
Acknowledgment This research was financially supported by the National Natural Science Foundation of China (Grant NO. 51274066).
Qin: submitted to Journal of Thermal Analysis and Calorimetry (2012)
Leion: International Journal of Greenhouse Gas Control Vol. 3 (2009), P.11-19.

RVM had been used effectively in scaling text classification[7], automatic speech recognition [8], medical science [9].
In this paper, a comparative experimental study on the assessment of RVM-GA, RVM, least square support vector machine (LSSVM) and back propagation neural network (BP-NN) for predicting the relationship between engine oil wear particle and fault is conducted based on ready-made data, which are selected as the materials of the spectrometric oil analysis(SOA) from an aero engine.
Flow chart of fault predict Data source In this paper, elements Fe, Al, Cu, Cr, Ag, Ti and Mg are selected as the materials of the spectrometric oil analysis(SOA), and their concentration form the original data of the SOA.
Journal of Nanjing University of Aeronautics ＆ Astronautics, 1999(2): 172-177
Chinese Journal of Biomedical Engineering, 2011, 30(6): 864-870

It is also important in determining fracture toughness and predicting fatigue life of materials [18] [20].
Cornec, “Material characterisation,” in SpringerBriefs in Applied Sciences and Technology, no. 9783642294938, 2013, pp. 17–31. doi: 10.1007/978-3-642-29494-5_3
Kala, “Four-Point Bending Test on a High Reinforced Concrete Beam: Nonlinear Numerical Analysis Using Material Parameter Identification,” in IOP Conference Series: Materials Science and Engineering, 2019. doi: 10.1088/1757-899X/471/5/052052
Lu, “Evaluation of RHT model for modeling concrete in numerical simulation,” in Progress in Mechanics of Structures and Materials - Proceedings of the 19th Australasian Conference on the Mechanics of Structures and Materials, ACMSM19, 2007, pp. 243–248.
Hamdia, “A Numerical Study of Crack Mixed Mode Model in Concrete Material Subjected to Cyclic Loading,” Materials (Basel)., vol. 16, no. 5, 2023, doi: 10.3390/ma16051916

Thermoelectric refrigeration is achieved when a direct current is passed through one or more pairs of n- and p-type semiconductor materials.
The TEC operates by the Peltier effect, which induces a temperature difference when an electrical current flows through a junction of dissimilar materials.
The usefulness of thermoelectric materials for refrigeration is often characterized by the dimensionless thermoelectric figure of merit ZT [1,7].
In the selection of a suitable TEC, the designs of the heat spreader and heat sink together with the interface materials could be crucial.
Yilmaz, “Design of a thermoelectric module test system using a novel test method,” International Journal of Thermal Sciences 46 (2007) 717–725

She will received the master’s degree in materials science from Beihang University, Beijing, 2013.
Journal of Electronic Materials.1999, 28(11):1231-1237 [9] Zhang Wei, Wang Chunqing, Yan Bohan.
Rare Metal Materials and Engineering. 2006, 35(7):1143-1145 [10] Yang Anheng, Xie Hongchao.
Welding Equipment and materials. 2005,34(4): 49-51 [12] Pan Hui, Sun Ji-Sheng, Liu Xiao-fang.
Journal of Aeronautical Materials. 2000, 20(4):26-29

Introduction High performance concrete (HPC) is characterized by a low water-binder (w/b) ratio and the use of supplementary cementitious materials (SCM) [1].
Experimental Program Commercially available Type I portlant cement and Grade 120 slag cement were used as the cementitious materials.
Wei, Modeling of Autogenous Deformation in Cementitious Materials, Restraining Effect from Aggregate, and Moisture Warping in Slabs on Grade, PhD Dissertation, University of Michigan, 2008
Ye, Materials Science-Based Models in Support of Internal Water Curing, in: K.
Hansen, Cryogenic suction as a major salt frost scaling mechanism in cementitous materials: submitted to Journal of Cement and Concrete Research (2014).

The problem of crack path stability along the interface between two orthotropic elastically dissimilar materials under the presence of in-plane residual stresses is analyzed using the concept of Finite Fracture Mechanics and matched asymptotic procedure.
As pointed out by Leguillon [2], the main role of residual thermal stresses in fracture problems of composite materials consists in modifying the stress intensity factor, which by the principle of superposition, can be expressed as the sum of mechanical loading contribution and thermal stresses contribution.
Analysis of the interface crack kinking usually brings difficulties with extension of the classical criteria for fracture in homogeneous materials in situations when the oscillatory index e defined by , (2) where β is the second Dundurs’ parameter, different from zero.
Journal of Eng.
Science Vol. 42 (2004), p. 257.