Search results

The result showed that grafting rate was reached 95.6%; IR spectrum proved that monomers have been completely reacted basically; thermal gravimetric analysis was characterized that the dust suppressant has good thermal stability between 0℃-250℃; the amount of AM and SDBS were 50% and 1.0% (based on mass of the total materials), the polymer has a suitable viscosity; SEM was used to observe the shape characteristic of the coal dust which formed a link between the dust suppressant and coal dust.
Experiment Materials.
The FT-IR characterized its structure, the results show that the raw material is enough reacted.
Mineral, Metallurgy, material. 2006, 13 (4), 368-371
Scientific Journal of Riga Technical University.

However, their comparison is contrastive in nature, since products, unlike the samples, are used as part of structures in a complex-stressed state, in contact with other more rigid materials [1].
Revealing the change patterns in rubber samples under these factors will determinea more reasonable choice of materials that are resistant to certain operating conditions.
Panfilova, Raw materials and materials for the rubber industry, KNITU, Kazan, 2015
Sokolova, Development of frost-resistant rubber based on epichlorohydrin rubber of Hydrin T6000 brand, Materials Science Forum. 945 (2018) 356-361
Effect of antioxidant on properties of thermoplastic natural rubber based on ENR/TPU blends, Advanced Materials Research. 626 (2013) 229-232

The interest in using recycled materials derived from construction and demolition waste is growing all over the world [2, 3].
Materials and Experimental Program Materials The materials used in the presented research are described as the following: Cement: Shaofeng 42.5 grade ordinary Portland cement made in Xiangxiang.
Material and structure, 33(2000), pp. 574-580
[6] Nobuaki Otsuki M.ASCE, Shin-ichi Miyazato, and Wanchai Yodsudjai: Influence of Recycled Aggregate on Interfacial Transition Zone, Strength, Chloride Penetration and Carbonation of Concrete, Journal of Materials in Civil Engineering, September/October (2003), pp. 443-451
RYU: Improvement on strength and impermeability of recycled concrete made from crushed concrete coarse aggregate, Journal of Materials Science Letters, 21(2002), pp. 1565-1567.

There are much more research on recycled aggregate as cement-bound crushed stones base materials.
Study on the workability and mechanical properties of recycled aggregate concrete containing ultra-fine fly ash [J], Key Engineering Materials, 2005, 314-320
Experimental research on the mix design and the modified of recycled aggregate concrete [J]，Journal of Railway Science and Engineering, 2005, 2（6）: 66-71
High performance cementing materials f rom indust rial slag —a review [J] .
Interfacial transition zone in cementitious materials[J].

Experimental Experimental materials The shale sample was obtained from Chaoyang, China.
In succession, the crashed materials were roasted in different conditions.
Curves of TG - DSC of the shale sample and mixed materials of mNaOH: mshale equal to 0.7 are depicted in Fig. 5, which shows that the melting temperature of mixed materials with NaOH is lower than that of original sample.
It can be showed from thermal analysis that the melting temperature of mixed materials with NaOH was lower than that of original sample.
D Earth Sciences, 35(5), pp 420-427

In these processes, the colloidal materials and other fine particles are easily adhere to SiC.
(3) In order to insure cutting efficiency, the mixtures of recycled SiC powder and standard materials are used.
Basic mechanisms and models of multi-wire sawing [J], Advanced Engineering Materials, 2004(6): 501-513 [3] LIN Feng,WANG Jian-ping,FU Jian-zhong.
Texturization of multi-crystalline silicon by wet chemical etching for silicon solar cells [J], Journal Of Materials Science, 2005, 40: 1459-1463 [5] Liu Zhidong,Qiu Mingbo,Wang Wei.
Effects of the Operation Parameters on the Air Classifier Performance [J], Journal of Sichuan University (Engineering Science Edition), 2006, 38(3):87-91

Materials and Methodology of Experiment The experimental work was carried out on unique instrumented equipment for experimental research of tube drawing.
Materials 6 (2013) 5118-5130 DOI:10.3390/ma6115118
Analysis of the Energy Vanished by Friction in Tube Drawing Processes with a Fixed Conical Inner Plug by the Upper Bound Method, Materials and Manufacturing Processes, 23:7 (2008) 690-697, DOI: 10.1080/10426910802317060 [5] F.
Journal of Materials Processing Tech. (2007) 182-186.
Journal of the Brazilian Society of Mechanical Sciences and Engineering, 27(4), (2005) 426-431.

Klimpel 5 1, 2 Division of Materials Processing Technology and Computer Techniques in Materials Science Institute of Engineering Materials and Biomaterials, Silesian University of Technology ul.
Tool steels still feature the widely used group of tool materials, especially interesting because of their low price and very good functional properties.
Polish Welding Journal, Warsaw, no. 6, 1999, p. 1-6
Polish Welding Journal, Warsaw, no. 8, 1999, p. 12-18
Barnes et al.: Journal of Materials Processing Technology 139, 2003, p. 585-588.

The main auxiliary materials are adhesives in process of plywood production.
Plastic is one of the four basic materials of modern industry [4].
It results in waste of raw materials, and has become global public nuisance.
Materials and methods Materials.
[4] Jingping Li, Nong Wang: Journal of Chemical Education Vol. 18 (2004), p. 2-3, in Chinese

The fundamental parameter to calculate the thermal performance, using an IR thermograph camera, of the envelope components is the emissivity of its materials surface.
Giorleo: Journal of Materials Processing Technology (2004), p. 1132
Brosse, A., et al.: Journal of Materials Processing Technology Vol. 201 (2008), p. 590
Science/Engineering/Math. 2009
Chen, J., et al.: Applied Surface Science Vol. 253 (2007), p. 9154.