Search results

Natarajan, “Effect of Low Feed Rate FSP on Microstructure and Mechanical Properties of Extruded Cast 2285 Aluminum Alloy”, Journal of Material Science Technology, vol 23, no.5 ( 2007), p. 614-618
Mishra, “Multiple Passes of Friction Stir Processing for the creation of Superplastic 7075 Aluminum”, Materials Science & Engineering 464(2007), p. 255-260 [5] P.Cavaliere, P.P.
De Marco, “Friction Stir Processing of AM60B Magnesium Alloy Sheets”, Materials Science & Engineering A 462 (2007), p. 393-397
Balasubramanian, “Selection of FSW tool pin profile, Shoulder diameter and Material for Joining AZ31B Magnesium alloy – An experimental Approach”, Journal of Materials and Design, Vol 30 (2009), p. 2647- 2656
Omar, “Friction Stir Processing of commercial AZ31 Magnesium alloy”, Journal of Materials Processing Technology, 191 (2007), p. 77-81

Babu: International journal of metals and materials, Vol.13, (2007), p.345-351
Idris and S.Farahany: Journal of composite materials, Vol. 47(10), (2012), p.1283-1291
[4] B.Roebuck: Journal of materials science letters, 6(10), (1987), p.1138-1140
[5] Sharma SS, Jagannath K, Prabhu PR, Gowri Shankar and Harisha SR: Materials Science Forum, Vol. 880, (2016) p. 140-143
Prabhukhot: International journal of material science and engineering, (2015), Vol.3 (4), p.287-294

Influcing Factor Research of Kerr Effect Runlin Guo1, Ningning Sun1, Mingxin Song1, a, Qian Liu1 1College of Applied Science, Harbin University of Science and Technology, Harbin 150080, China asongmingxin@126.com Keywords: Kerr effect; Kerr cell voltage; Duration time; Electrode material; Abstract.
When materials of anode and cathode are different, changes of the four curves seem not to be in noteworthy synchronization; The fluctuations of curves are so weak that most parts of the four curves are overlapped.
When the cathode material is iron, regardless of anode material is aluminum or brass, the curves show little change.
Acknowledgements The work is supported by the Project of Student Innovation Fund in Harbin University of Science and Technology Harbin.
Clem: submitted to Journal of Materials Research (2007) [4] Yeh,Y.

The TBC and bond coat were modeled as elastic-viscoplastic materials.
Takeuchi: Materials Science and Engineering A 189 (1994), p. 301
Taylor: Materials Science and Engineering A299 (2001), p. 296
Kokini: Mechanics of Time-Dependent Materials Vol. 6 (2002), p. 171
Taylor: Materials Science and Engineering A Vol. 323 (2002), p. 70

This paper shows the effect of sustainable copper fibres on some properties of perlite structural lightweight concrete containing sustainable materials.
The materials used to cast the specimen are ordinary Portland cement, local ash, metakaolin, combined coarse and fine perlite aggregate, and super-plasticizer.
Experimental Work Materials.
Vrcelj, “Current sustainable trends of using waste materials in concrete—a decade review,” Sustainability (Switzerland), vol. 12, no. 22.
Nugraha, “High strength lightweight concrete with expandable perlite as the aggregate,” in IOP Conference Series: Materials Science and Engineering, Institute of Physics Publishing, May 2020. doi: 10.1088/1757-899X/830/4/042040

The analysis shows that the latex cement can be used for deep soft rock rheology theory and polymer materials similar simulation experiment.
The mechanical properties of the deep soft rock are impacted by the environmental deep rock mass and are difficult to be simulated by actual materials, it is relatively easy that the application of latex cement as the similar material to simulate deep soft rock.
This conclusion is consistent with the experimental data，it proves that a reasonable proportion of the latex cement can be used as a soft rock similar materials.
Acknowledgements This work is financially supported by State Key Laboratory for GeoMechanics and Deep Underground Engineering Open Foundation(SKLGDUEK1022), National Natural Science Foundation (50974077) and National Natural Science Foundation (51074094).
Journal of China Coal Society, 2010，35(7)：1095—1098 , In Chinese

Tsai, "Micro-hole machining of carbide by electric discharge machining," Journal of Materials Processing Technology 87 (1999) 139–145
Lauwers, "EDM technology and strategy development for the manufacturing of complex parts in SiSiC," Journal of Materials Processing Technology 210 (2010) 631–641
Puertas, "Methodology for developing technological tables used in EDM processes of conductive ceramics," Journal of Materials Processing Technology,189 (2007) 301–309
Villa, "Spacing roughness parameters study on the EDM of silicon carbide," Journal of Materials Processing Technology, 164–165 (2005) 1590–1596
Singh, "MRR Improvement in Sinking Electrical Discharge Machining: " Journal of Minerals & Materials Characterization & Engineering, 9 (2010) 709-739

There is also another innovative method that involves using phase-change materials (PCMs) to remove heat from PV panels.
Thermal Management Improvement in Photovoltaic Cells using Phase Change Materials.
Materials and Methods Physical Model Description and Specifications.
Gendeshmin, “Improvement of photocells by the integration of phase change materials and thermoelectric generators (PV-PCM-TEG) and study on the ability to generate electricity around the clock,” Journal of Energy Storage, vol. 36, Apr. 2021
Hegedus, Handbook of photovoltaic science and engineering.

As other ceramic materials, glass presents a brittle behaviour and a broad scatter of strength results, due to the random distribution of micro-cracks on its surface.
The resistance of brittle materials can be analysed using two different approaches: a critical stress model [6] and a maximum defect size model [7].
Deriving the primary cumulative distribution function of fracture stress for brittle materials from 3- and 4- point bending tests.
Journal of European Ceramic Society, 31, 451-460, 2011
Computational Material Science.

And the leather wastes are the raw materials of collagen.
Experimental Materials.
Journal of Applied Polymer Science. 68(1998), 1109-1115
Journal of Applied Polymer Science. 75(2000), 987-993
Journal of Materials Science Letters, 8(1989), 1307-1309