Search results

Materials The material at the centre of this investigation is the hardenable aluminum alloy AA6082 (AlMgSiMn) with a sheet thickness of 2.5 mm.
For increased accuracy for anisotropic materials, a refined yield criterion is required.
Ma: Friction stir welding and processing, Materials Science and Engineering R 50 (2005), 1–78 [3] G.
Fratini: Design of the friction stir welding tool using the continuum based FEM model, Materials Science and Engineering A 419 (2006), 381–388
In: Journal of the Mechanics and Physics of Solids, 23 (1975), 87-98 [18] E.

Rezan Sheikh Abdul Hamid, Hashim Hussin School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia,Penang, Malaysia, norlia@eng.usm.my Keywords: Carbothermal Reduction, Factorial Design, Malaysian Ilmenite, Nitridation.
Experimental Method The raw materials that were used to synthesize TiOxCyNz are Malaysian ilmenite, coal, and FeCl3 (catalyst).
[3] Coley, K.S, Ph.D Thesis, Imperial College of Science and Technology, London, United Kingdom, 1986
El-Midany, “An assessment of the carbothermic reduction of ilmenite ore by statistical design”, Journal of Materials Processing Technology, Vol. 199(1-3) (2008) p.p: 279-286
Grieveson, “Kinetics of reduction of ilmenite with graphite at 1000 to 1100 °C”, Metallurgical and Materials Transactions B, Vol. 18(4) (1987) p.p:713-718.

The crusher dust is widely considered as inert material that is not a party to hydration reaction, but in some investigations it is deduced that the limestone powder can stimulate and enhance hydration of cement.
Raw Materials and Experimental Methods Raw Materials.
Key Engineering Materials, 2006 Vols. 302-303: 263~268 [2] Ji-Wei Cai, Bei-Xing Li, Ming-Kai Zhou, Xiao-Man Hu.Effecets of crusher dust on properties of low/medium strength concrete with manufactured sand [J].
Journal of Wuhan University of Technology, 2006, 28(4):27~30 [3] V.
Journal of Wuhan University of Technology (Materials Sciences Edition), 1996, 11(4): 29~34 [5] Hiroshi Uchikawa, Shunsuke Hanehara, Hiroshi Hirao.

Gasification efficiency is defined as the ratio of the chemical energy of gasifying gas to the raw materials.
The ratio of the content of the carbon in the gasification gas to the raw materials is carbon conversion rate.
Acknowledgements This work was financially supported by the the National Natural Science Fund of China (51036002) and Sichuan Province Major scientific and technological achievements into the project funding (11CGZH0025).
Yan: Chinese Journal of Chemical Physics (In Chinese).
Vol. 18 (2005), p. 74 [3] K .Zhang: Journal of Fuel Chemistry and Technology.

Quality assessment of welded joints by the metal magnetic memory method compared to conventional ndt methods and means for materials properties assessment. 17th World Conference on Nondestructive Testing.
Fundamental research on deformation characterization of ferromagnetic materials by metal magnetic memory testing.
Journal of Academy of Armored Force Engineering.3 (2010) 68-71
Journal of physics D: applied physics. (1995) 1537-1546
Physical model of plastic deformation on magnetization in ferromagnetic materials.

Further analysis showed that the green highlights of the vast majority of projects were reflected in the application of equipment, techniques and materials, and even some projects were up to the standards after the adoption of high-cost active technologies or materials for “patching” in the stage of construction drawing.
Connotation and Economic Features of Green Building 1.1 Connotation of Green Building According to the new version of the Evaluation Standard for Green Building, green buildings refer to those that maximize conservation of resources (energy, land, water and materials), the protection of environment and the reduction of pollution, provide people with healthy, applicable and efficient space and coexist with the nature in harmony in their full life circle.
In addition, as the charging base of design fee is subject to project cost, when the design of green building is more “green”, the use of high-cost technical equipment and materials will be correspondingly reduced and project cost will decrease, thus resulting in a corresponding reduction in design fee.
Qin Youguo [6] once emphasized that “in order to deepen the study of ecological design, architects must pay attention to building technology and science, and ecological building belongs to the laws of physics rather than modeling game”.
Architectural Journal,07 (2013) p. 94-99 [4] Zheng Shiling: Building Criticism [M].

Introduction The demand for sustainable printing materials has led to a focus on environmentally friendly ink formulations, particularly those derived from renewable sources such as palm oil.
Previously, several materials have been used by researchers as a substitute for petroleum for development of vegetable-oil based ink such as Linseed oil [5]; Karanja Oil [6], Soybean Oil [7], Safflower oil [8], [9], and Grapeseed oil [8].
Methods Materials.
Ateş Duru, “An ecological approach to printing industry: Development of ecofriendly offset printing inks using vegetable oils and pine resin as renewable raw materials and evaluation of printability,” Color Res Appl, no.
Dendge, “Print Quality Evaluation in Paperboard Printing Induced by Changes in Viscosity and Screen Parameters,” SAMRIDDHI : A Journal of Physical Sciences, Engineering and Technology, vol. 15, no. 01, pp. 133–138, Jan. 2023, doi: 10.18090/samriddhi.v15i01.18

FSP has been successfully applied in various materials such as magnesium alloys [15, 16], aluminum alloys [17, 18] etc to improve their mechanical properties through microstructural refinement.
Teti, Machining of Composite Materials.
[7] Rafal Rusinek, Cutting process of composite materials: An experimental study, INT J NONLIN MECH. 45 (2010) 458–462
Elaya Perumal, Taguchi Analysis of surface roughness and delamination associated with various cemented carbide K10 end mills in milling of GFRP, Journal of Engineering Science and Technology. 3 (2010) 58-64
Ramachandra, Delamination analysis in drilling process of glass fiber reinforced plastic (GFRP) composite materials, J MATER PROCESS TECH. 186 (2007) 265-271

The interphase characterization of the nanostructured materials synthesized was performed using FT-IR analysis.
The interphase characterization of the nanostructured materials synthesized was performed by infrared spectroscopy.
Hon, in: Chemical Modification of Lignocellulosic Materials.
Tannenbaum: Journal of Physics and Chemistry, B, Vol. 107 (2003), p. 12097-12104
Wolter: Solid State and Material Science, Vol. 4, Nr. 55 (1999)

When a comprehensive modal analysis was finished, a modal neutral file concluding the information of crankshaft material, nodes, elements and modal was written out.
Vancouver, Holzer method for forced-damped torsional vibrations, Journal of Applied Mechanics. 17 (1950) 59-63
I: Background and application to free vibrations, Journal of vibration and acoustics. 117.1 (1995) 70-79
Journal of vibration and acoustics. 117.1 (1995) 80-86
[13] Chengwu Liu, Dynamic analysis and noise prediction of large-scale compressor, Nanjing University of Science and Technology. (2006).