Search results

On the other hand, the contrary conclusions can be derived for diamagnetic materials.
And part of this work was performed at high field laboratory for super-conducting materials, Institute for Materials Research, Tohoku University.
Iwai and S.Asai: Materials Transactions, Vol.42(2001), p.275 [12] H.O.
Lindroos: Scandinavian Journal of Metallurgy, Vol.10(1981), p.3 [13] Z.
Mater., Vol.43(2000), p.221 [17] K.Watanabe and M.Motokawa: Materials Science in Static High Magnetic Fields, (Springer, Berlin 2001)

Sepiolite mineral nanofibers are typical porous materials widely existing in nature and have many nanometer level micropore and mesopore, which could play an active role in many fields such as thermal insulation functional additive for composite materials.
Composite materials were characterized by SEM and TEM.
Moya, et al.: Journal of the European Ceramic Society, vol. 28(2008), p.1763 [5] A.
J.Fripiat: Microporous Materials, vol. 5(1995), p.135 [6] R.
Camino: Materials Science and Engineering: C, vol. 29(2009), p.1433 [15]N.

Journal of Yangtze River Scientific Research Institute, 2005:22(1):60-62
Journal of Hunan University, 2009:36(9):51-54
Advanced Materials Research, 2012:382:137-140
Experimental research on properties of materials of grounding resistor.
Research Journal of Applied Sciences, Engineering and Technology, 2013:5(9):2858-2862

Silberschmidt, Finite element modelling of thermally bonded bicomponent fibre nonwovens: tensile behaviour, Computational Materials Science 50 (2011) 1286-1291
Desai, Review of thermally point-bonded nonwovens: materials, processes, and properties, Journal of Applied Polymer Science 99 (2006) 2489-2496
Silberschmidt, Finite element simulation of low-density thermally bonded nonwoven materials: Effects of orientation distribution function and arrangement of bond points, Computational Materials Science 50 (2011) 1292-1298 [14] X.
Silberschmidt, Non-uniformity of deformation in low-density thermally point bonded non-woven material: effect of microstructure, Journal of Materials Science 46 (2011) 307-315 [15] X.
Silberschmidt, 2D finite element analysis of thermally bonded nonwoven materials: Continuous and discontinuous models, Computational Materials Science 46 (2009) 700-707

Later it was used as filter material in oilfields.
Table2 The cleaning formula of regenerant Materials NaOH Na2SiO·（9H2O） Na5P3O10 Na2CO3 OP-10 HO(CH2CH20)nH H2O LAS Mass(g) 4.5 6.5 2.0 3.5 6.5 25 75 1 The concentration and temperature of regenerant and the amount of LAS Fig.1The relationship of detergent concentration Fig.2.
Rahman: Journal of Petroleum Science and Engineering. 7(1992), P.244
（In Chinese） [6] Palladino, P, Rossi, F and Ragone, R: Journal of Fluorescence. 20(2010), P. 191
L, Elistratova, J, Soloveva, S, Garusov, A, Antipin, I and Konovalov, A:Journal of Colloid and Interface Science. 346(2010), P.405

The burr formation experienced three stages: First, Copper foil extrudes with the feed of microdrill; Second, Most of the Materials are cut off by drill tip and the rest of material; At last, rollover burrs appear when drill enters or exits uncut chip rolls.
There are many results in PCB or composite materials drilling.
The thrust force was measured by Kistler 9317B.Experimental materials are listed as follows: 0.1mm thick aluminum board; (2) 1.5mm thick PCB.
So the burr formation experienced three stages: (Ⅰ) Copper foil extrude with the feed of microdrill; (Ⅱ) Most of the Materials are cut off by drill tip and the rest of material; (Ⅲ) rollover burrs appeare when drill enters or exits uncut chip rolls.
(2) The burr formation experienced three stages: First, Copper foil extrudes with the feed of microdrill; Second, Most of the Materials are cut off by drill tip and the rest of material; At last, rollover burrs appear when drill enters or exits uncut chip rolls

Journal of Materials Processing Technology, 2000(105): p95-109
Journal of Materials Processing Technology, 2004(146): p82-91
Journal of Materials Processing Technology, 2004(146): p72-81
Journal of Materials Processing Technology, 2000(98): p99-103
International Journal of Mechanical Sciences, 1999(41): p941-965

Advanced Materials Research.
Thermal fatigue of materials for die-casting tooling [J].
Materials Science and Engineering.
Materials and Manufacturing Processes.
Three-dimensional cell model analyses of void growth in ductile materials [J].

Experiments Raw materials Raw materials such as anthracite fine, petroleum coke powders and charcoal powders were provided by a factory of Yunnan Province, and the chemical position is shown in Table 1.
Journal of Wuhan University of Technology (Materials Science Edition), 2014, (1):75-81 [5] Mingyi ZHENG, Kun Wu, Congkai YAO.
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2001, 17(1):21-22 [6] T.M.
Construction and Building Materials, 2013, 44: 207-213
Journal of Materials Processing Technology, 2010, 210(6): 961-968

The Interlayer Designation for ZTM Ceramics and Fibre Joining Yingna Zhao 1,2,a, Jiachen Liu1,b, Caifen Wang1 and Wenli Zhang2,c 1School of Materials Science and Engineering of Tianjin University, Tianjin, China, 300072 2School of Materials Science and Engineering of Hebei United University, Tangshan, Hebei, China, 063000 ayingna_1120@sohu.com, bjchl@tju.edu.cn, c tszhwl@126.com Keywords: ZTM ceramics, Ceramic fibre, Al-Si alloy, Microwave joining.
The joining materials of density ceramics and the fibre would be potential application value as seal materials at high temperature condition or in aerospace field.
Singheiser, Journal of Power Sources.
Schwarz, Journal of Nuclear Materials.
Knowles, International Materials Reviews.