Search results

Acknowledgements This work was financially supported in part by the Natural Science Foundation of China (51278373), and the Natural Science Foundation of Liaoning Province (201202180), as well as the Science Foundation of Liaoning Education Department (L2012214).
Mal: Journal of Intelligent Material Systems and Structures Vol.18 (2007), p.91
Boller: International Journal of Systems Science Vol. 31-11(2000), p.1333
[3] V.Giurgiutiu: Journal of Intelligent Material Systems and Structures Vol. 16(2005), p.291
Kaczmarek: Journal of Composite Materials, Vol.37-3 (2003), p.987.

The wide use of chemical activators that show dehydration, etching effect towards raw materials, include KOH, H2SO4, ZnCl2, NaOH, etc.
First, treat raw materials with chemical immersion treatment, and then with the gas physical activation.
Jin, et al.: Chinese Journal of Environmental Engineering.
Parra, et al.: Chemical Engineering Journal Vol.114 (2005), p.161-169
Bandosz: Journal of Colloid and Interface Science Vol. 302 (2006), p. 379-388

· Ductile materials and high stresses
Shivpuri, Prediction of chip morphology and segmentation during the machining of titanium alloys, Journal of Materials Processing Technology 150 (2004) 124–133
%V alloy, Materials Science and Engineering A 190 (1995) 173–180
CIRP Journal of Manufacturing Science and Technology 1 (2008) 81–85
Journal of Materials Processing Technology 167 (2005) 1–13

The oxidizing atmosphere reduces the SO2 emissions, improves the burnability of raw materials, promotes the formation of calcium sulphoaluminate and thus increases the desulfurization degdree.
Journal of fuel chemistry and technology.
Journal of china coal society.
Journal of northeastern university (Natural science).
Journal of mineralogy and petrology.

Highly ordered metallic nanowire arrays were particularly important for electronic and photoelectronic devices, materials science, magnetics, optics and for its application to micro- and ultra-filtration.
Li: Materials Letters, 59(2005), p. 1223-1226
Ni: Journal of Magnetism and Magnetic Materials, 234(2001), p. 454-458
Doudin: Journal of Magnetic Materials, 165(1997), p. 34-37
Dieny: Journal of Magnetism and Magnetic Materials, 195(1995), p. 437-451

Abstract.Reinforced soil has been among the most effective soil modification materials.
The advances of these materials have usually been considered by an increase in their applications.
MATERIAL Composite materials consist of two parts.
REFERENCES [1] Akbulut, S., Arasan, S. and Kalkan, E. (2007) Modification of clayey soils using scrap tire rubber and synthetic fibres, Journal of Applied Clay Science 38, 23-32
[5] Chegenizadeh, A. and Prof.Hamid Nikraz ,”Composite Soil: Fibre Inclusion and Strength”, Journal of Advanced Materials Research,1646, 2011 [6] Chegenizadeh, A. and Hamid Nikraz ,Interaction of soil and short fibre, , ASTM digital library,2011 [7] Chegenizadeh, A. and Hamid Nikraz, Composite Clayey Sand and Short Fibre, Advanced Materials Research Journal [8] Freitag, D.R. (1986) Soil randomly reinforced with fibres, Journal of Geotechnical Engineering ASCE 112 (8), pp. 823–826

Moreover, the material is generally presumed to be rigid perfectly plastic.
Their theoretical model assumes an elastic plastic material with linear strain hardening.
The authors gratefully acknowledge the support by Warsaw University of Technology under Grant No N501 156038, Ministry of Science and Higher Education (Poland).
Symonds, Large deformations of beams under transverse impast, Journal of Applied Mechanics 19 (1952) 308-314
Nowacki, New applications of Hopkinson's pressure bar technique for determining dynamic behaviour of materials, Journal of Theoretical and Applied Mechanics, 34 (1996) 259–280.

In recent years, with the deep research on new materials, both the traditional plastic cushioning materials such as EPE, EPS, and the paper-based cushioning materials such as honeycomb paperboard, corrugated cardboard are widely used.
In the derivation process of equation (9), there is not any linearity assumption of the material, so the equation is applicable to the overlay combination of linear materials and non-linear materials.
Parallel pads were usually made by same materials.
The C-curves of two materials are shown in Fig.2.
(In Chinese) [4] Z.W.Wang and Y.P.E: Materials and Design, vol. 31 (2010), pp. 4321–4328; [5] D.Gao and F.D.Lu: Journal of Vibration and Shock, Vol. 29 (2010) No.10, pp. 131-136.

During past few years, the Split Hopkinson Pressure Bar (SHPB) has been widely used to determine the constitutive model parameters for some metal materials [11].
Carroll, “A finite element model of orthogonal metal cutting”, Journal of Manufacturing Science and Engineering, 1985, 107(4): 349-354
Qi, “Thermal and thermo-mechanical modeling of friction stir welding of aluminum alloy 6061-T6”, Journal of materials processing and manufacturing science, 1998 (7): 215-233
Strenkowski, “Finite element models of orthogonal cutting with application to single point diamond turning”, International Journal of Mechanical Sciences, 1988, 30(12): 899-920
Mann, et al, “Stability of interrupted cutting by temporal finite element analysis”, Journal of Manufacturing Science and Engineering, 2003, 125(2): 220-225

Due to the above mentioned merits, the PLA materials have been widely used in food packaging field, nonwovens applications and consumer packaged goods as the most promising new materials [11-12].
Therefore study of modified PLA to improve the stability of the materials become more active by researchers [14-15].
Material and methods Materials.
Niu: Journal of Functional Materials Vol. 39 (2008), p. 123-126 [3] M.G.
Cao: Journal of Anhui Agricultural Sciences Vol. 31 (2010), p. 17384-17386 [15] G.D.