Search results

Mahajan: The Encyclopedia of Advanced Materials (1994), p. 2455
Nishimura: Journal of the European Ceramic Society Vol. 23 (2003), p. 2023
Aldinger: Materials Science and Engineering A Vol. 374 (2004), p. 56

Introduction The biological carrier can form a large biomass, abundant bio-phase biofilm, and highly effective degeneration sewage, is an important environmental materials.
Li, et al: Materials Science Forum Vol. 575-578 (2007), p. 385
Li, et al: Journal of South China University of Technology Vol. 36(2008), p. 75

F.Wang, W.B.Zhang, X.F.Zhang, et al: International Journal of Heat and Mass Transfer, 54 (2011), p.1002
Xu: Master Thesis of Huazhong University of Science and Technology, 5(2009)
Wang: Advanced Materials Research, 139-141(2010), p. 881
Liang: Applied Mechanics and Materials, 29-32(2010), p. 2490.

Compared with general machining and forging process, precision forging method can form gear’s tooth directly without machining, which can improve the properties and save materials.
In common cold finish forging process, decrease of the gear free surface may cause confined flow of the material.
Top die is the master, its velocity is 35mm/s, and its material is 65Ni.
The bigger the diameter, the more the material flows to the center hollow, result that it is more difficult to fill in the tooth.
Journal of Zhejiang University of Science and Technology, Vo l. 21 No. 3, Sep. 2009, p.200-203 [4] Zezhong Chen, Zhongxu Bao, Shuqin Lian, Zhiping Lin.

The parameters of temperature loads and material are shown in the Table 1.
A eight-node element with three degrees of freedom—axial displacement and radial displacement was selected for materials’ simulation.
References [1] Anna Saetta, Roberto Scotta, Renato Vitaliani, Stress analysis of concrete structures subjected to variable thermal loads, Journal of Structural Engineering. 1995,Vol.121 (3),446-457
[2] Haidong Zhao, Zhao Ming, Shuiming Shen, Temperature response of super-length concrete structure, Building science research of Sichuan. 2000,26 (4),7-9
[6] Zhijian Huang, Xiaojie Lao, Wu Hang, Kaihang Zhou, Temperature cracks control of over-long reinforced concrete frame structure, Journal of qinzhou university, 2008, 23 (6),47-50

BeiJing: China building materials industry press，2008
Pile foundation design and calculation [M].BeiJing: China building materials industry press,1990, 211-216
Effect of Vertical Load on the Horizontal Bearing Capacity of Piled Foundation [J].Journal of Shantou University (Natural Science), 2008, 23(3):32-37
Journal of the Geotechnical Engineering, 1988,114 (11): 1261-1276

Well-established Biodegradation Tests Used Biogenously Evolved Carbon Dioxide as an Analytical Parameter to Determine the Ultimate Biodegradability of Metalworking Fluids Measured by the Change of Absorption Solution Conductivity Gerulova Kristina1,a 1 Slovak University of Technology in Bratislava, Faculty of Materials Science and Technology in Trnava, Department of Environmental Engineering, Paulinska 16, 91724 Trnava, Slovak Republic akristina.gerulova@stuba.sk Keywords: Metalworking fluids, Biodegradability, Carbon dioxide, Conductivity Abstract.
This value is then compared to the theoretical amount of CO2 which could be generated if all of the carbon in the test material were converted to CO2.
Material and Methods It was constructed an apparatus according the [5] and this is shown in the Fig. 4a.
International Journal of Machine Tools & Manufacture. 52 (2012), p. 1–12 [2] Pettersson, A.
Polish Journal of Environmental Studies.

Acknowledgement It is a project supported by the National Science Council (No. 101-2221-E-252-007）.
Color figures are welcome for the online version of the journal.
Mishing, in: Diffusion Processes in Advanced Technological Materials, edtied by D.
Clem: submitted to Journal of Materials Research (2003) [6] P.G.

Mainly they are the remains of the technological cooling fluid, remains of the solid particles of the material of grinding wheel and metal material removed from the machined object.
Typical impurity on roller's head: a) whole surface in liquid, b) individual liquid's dot, c), d) stain of liquid on the grinding surface, e) solid parts of grinding material (all pictures taken with the same light conditions) The method description To fulfil the requirements of the vision methods the roller must be cleaned from the gathered impurities before the inspection process [3, 4].
After cleaning, in different lighting conditions, several defects could be exposed, such as grinding defects, forging defects, hardening defects, material lacks and corrosion.
O’Leary, Visual inspection of machined metallic high-precision surfaces, Journal on Applied Signal Processing 7 (2007) 667-678
International Journal of Simulation Systems, Science & Technology.Special Issue on Intelligent Systems Engineering.

Skolud, Production preparation and order verification systems integration using method based on data transformation and data mapping, Lecture Notes in Artificial Intelligence, Lecture Notes in Computer Science. 6679 (2011) 397-404
Olender, Production planning and control using advanced simulation systems, International Journal of Modern Manufacturing Technologies.
Skolud, Transient States of Cyclic Production Planning and Control, Applied Mechanics and Materials. 657 (2014) 961-965
Advanced Materials Research. 837 (2014) 416-421
Liao, Scheduling flexible job shop problem subject to machine breakdown with game theory, International Journal of Production Research. 52 13 (2014) 3858-3876