Search results

Hodzic, A graphical method predicting the compressive strength of toughened unidirectional composite laminates, Applied Composite Materials 18 (2011) 65-83
Smaali, Experimental study of long T300 carbon fibre undulations during the curing of LY556 epoxy resin, Composites Science and Technology 67 (2007) 2633-2642
Seferis, Nanoclay reinforcement effects on the cryogenic microcracking of carbon fibre/epoxy composites, Composites Science and Technology 62 (2002) 1249-1258
Hodzic, Effect of silica nanoparticles on compressive properties of an epoxy polymer, Journal of Materials Science 45 (2010) 5973-5983
Yurgartis, Measurement of small angle fiber misalignments in continuous fiber composites, Composites Science and Technology 30 (1987) 279-293.

It can reduce material waste while lighting the parts weight by using this method.
Fig. 3 Equivalent model of TRB rolling Materials and Initial Conditions.
Select the AISI-1043 as material of sheet.
Hirt: International Journal of Machine Tools & Manufacture, Vol. 48 (2008), pp.522-531 [3] Y.H.
Zhao: Experimental Design ( Science Press, China 2006) (In Chinese)

The hard degradation material by the conventional technique could be transformed into the easy degradation material, therefore the biodegradation rate could be improved and the residual sludge could be reduced [2].
Their strength and stiffness all meet the requirement of the national synthetic material standard.
[3] Wenjin Tong, Shuiyu Sun, Baojian Liu, etc: Chinese Journal of Environmental Engineering, 2012, 6(1):68-72, In Chinese
[4] Jianguo Jiang,Yan Zhang, Qunfang Zhang, etc: Environmental Science, 2008, 29(10):2815-2819, In Chinese
[6] Wenjin Tong, Shuiyu Sun, Li Zheng, etc: Environmental Science & Technology, 2010, 33(5):133-139, In Chinese

Experimental Unit The experiments were performed in Energy Research Institute of Shandong Academy of Sciences key lab.
It concludes material circulating system, air induced draft/supply system, pressure and flow rate measuring system.
Then the particles return to the riser through the seal loop and form the material circulation.
Chemical Engineering Science, vol.61, pp.5544–5559
International Journal of Multiphase Flow, vol.26, pp.387-419

According to the actual material properties, elastic modulus is set as 2 e + 11 [Pa] and 1.1 e+11 [Pa], Poisson ratio is 0.3 and 0.35.
According to the material properties, the definition of the friction coefficient is 0.1.
As we know, the friction coefficient is determined by the roughness of the joint surface when the materials of the contact pair are chosen.
This paper was supported by the Important Science and Technology Research Project of Chongqing—Project Numbers (CSTC2007AA7003). 2.
Wang: Journal of Gansu Science, Vol.21 (2009) No. 4, pp.97-99 (in Chinese)

Introduction Broomcorn-stalk is green, non-toxic and low price material.
That drugs are prepared by using green materials as accessories is the development trend.
Broomcorn-stalk is green material for being natural material.
Chen and X.Z Liu: Chinese Herbal Drug Research Trends, Nova Science Publishers, Inc. 2007, p.147 [2] Z.F.
Ran: Chinese Journal of Synthetic Chemistry Vol.5 (2008), p. 611 [9] X.Z.

Agricultural irrigation water reach quickly the lower edge of over-cutting, overgrazing causes increasingly serious damage, many places already appeared land desertification, fixed dune activation phenomenon, cause farmland decreases ceaselessly. 2.4 Solid waste and noise pollution is becoming more serious As a result of Urumqi city population concentration, but the relative District stricture, to the processing of raw materials consisting mainly of industrial solid waste emissions is larger, but the utilization of waste residue is much lower, and the waste emissions is also huge, rubbish and processing of the space is limited, therefore, solid waste pollution is increasing; industrial noise and exceed the standard, and there is an upward trend. 2.5 Traffic is more crowded At present, traffic congestion was so serious due to overall planning of Urumqi city is not reasonable, and not expected growing speed of vehicle so fast, the road width remained inadequate, road edges from the building
He is in accordance with the principle of ecology, trying to establish an economic, social and natural three coordinated development, material, energy and information utilization, a virtuous circle of ecological human settlements, which is efficient, harmonious human habitat.
and technology guide mode Through strengthening scientific research institutions and colleges and universities to develop new materials development, resources and environment of new technology development and industrialization, accelerate the construction of ecological city. 4.5 Groups of driving mode Play through the city community organization, guide and organize community broad participation of the masses of ecological city construction. 4.6 Urban and rural interactive pattern Through the implementation of urban and rural economy, society, zoology integrated planning, promoting urban rural interaction development, accelerate the construction of ecological city. 5 Problem solving strategies and Countermeasures The government should give full play to the function, optimize the city overall planning, special attention should be paid to city ecological planning, and increase the investment in construction of ecological city.
It is to strengthen innovation of science and technology foundation function, promote achievement of science and technology applied to city ecological planning and ecological construction.
Journal of Urumqi Vocational University,2008(4): 10-12 [4] Yi Qian, Jianwen Zhu.

As the rapid development of science and technology, strawberry preservation technology research is in the direction of the security, low consumption, high efficiency, environmental protection development.
Experimental Materials.
Due to this gas flow was controlled by suitable barrier properties of packaging material, equilibrium was achieved.
[4] Wang Jianqing, Yang Yan, Jin Zhengwei: Journal of Tianjin University of Science & Technology 26 (2011), p.10-13
Tzortzakis: Innovative Food Science and Emerging Technologies 8 (2007), p.111-116

Effect of pin material on COF & wear.Testing was carried out on LST discs made of HSS and pin material of type MS, EN31 and SS under dry and wet condition.
The least efficient amongst the group of pin materials was MS, which showed Highest COF and wear parameter readings for both Wet and Dry conditions.
· The wear and friction trends revealed innovative technique and novel knowledge in terms of structure and surface quality for science of tribology.
References [1] Wakuda M., Yamauchi, Y., “Effect of Surface Texturing on Friction Reduction Between Ceramic and Steel Materials under Lubricated Sliding Contact”, Wear, 254, pp. 356–363
Proceeding of IMechE Journal of Engineering Tribololgy (Part J), 225, 693–703

Kosarev High-energy processing of materials/ Novosibirsk: Science. 2000. 425 p
Electrolyte plasma nitriding of high speed steel // Applied Mechanics and Materials (ISSN: 1662-7482) Vol. 379 (2013) pp161-166
Surface treatment of materials with low-energy. high-current electron beams.
Charter 6 in Book "Materials surface processing by directed energy techniques". - Ed.
Investigations into the  effects of electron beam welding on thick Ti6Al4V titanium alloy // Journal of Materials Processing Technology,2007,192−193: 83−88