Search results

Ng, European Journal of Operational Research, Vol. 164, (1) (2005),p. 64-78
Ismail, Advanced Materials Research, in press
Ng, European Journal of Operational Research, Vol. 164, (1) (2005), p. 64-78
Vis, et al., Flexible Services and Manufacturing Journal (2013), p.1-39
Ariffin, International Journal of Physical Sciences, Vol.6 (27) (2011), p. 6286-6294.

Journal of Applied Meteorology. 1976;15:301-6
Journal of Geophysical Research: Atmospheres (1984–2012). 1998;103:9035-44
Journal of Geophysical Research: Oceans (1978–2012). 1982;87:11203-14
Journal of Geophysical Research: Atmospheres. 2013;118:12,879-12,92
Applied Mechanics and Materials: Trans Tech Publ; 2014. p. 561-5.

Materials and Experimental Procedures The studied alloy is aluminium 1050 and it is a commercially available material with Al-0.3 wt% Fe with minimum solute content providing with an almost single phase.
Sidor, “Review: Deformed and recrystallized structures in FCC materials,” eis, pp. 21–35, Dec. 2021, doi: 10.37775/EIS.2021.2.3
Zhang, “Effect of Annealing Process on the Microstructure and Texture of Cold-Rolled High-Purity Al-0.5%Cu Plates,” Materials, vol. 15, no. 10, p. 3489, May 2022, doi: 10.3390/ma15103489
Fang et al., “Evolution of texture, microstructure, tensile strength and corrosion properties of annealed Al–Mg–Sc–Zr alloys,” Materials Science and Engineering: A, vol. 804, p. 140682, Feb. 2021, doi: 10.1016/j.msea.2020.140682
Gao, “Indentation size effects in crystalline materials: A law for strain gradient plasticity,” Journal of the Mechanics and Physics of Solids, vol. 46, no. 3, pp. 411–425, Mar. 1998, doi: 10.1016/S0022-5096(97)00086-0

Typical ballast track cross-section Shear strength for granular materials is to vary linearly with the applied stress.
Test Materials and Method Ballast aggregates used in the present investigation is gravels.
This conditions happen when the stress been applied on the materials, then the materials strains or deforms.
The higher stress is applied, the more strain happen on the materials.
Financial support was made possible by the Science Fund (S025) from Ministry of Science, Technology and Innovation.

With the structure size and material properties, the relationship curve between vacuum gauge output and gas pressure can be obtained.
Device fabrication starts by depositing 0.5μm PECVD SiO2 on the back side of a (100) silicon wafer which is used as the masking material in the following wet etching process.
This work is supported by the grant of Science and Technology Development (No.2012A0403018) in China Academy of Engineering Physics.
Vacuum Science and Technology 1997, 17(5), 330-335
Journal of Micromechine and Microengineering. (2009)1-8

It is restricted to low X-ray energies and thus to low density materials.
Schors, X-ray refraction characterization of non-metallic materials, NDT&E International 34 (2001) 297-302
Klobes, Characterisation of porous titania yttrium oxide compounds by mercury intrusion porosimetry and X-ray refractometry, Journal of Porous Materials 18 (2011) 83-88
Heutling, Refraction computed tomography, MP Materials Testing 46 (2004) 314-317
Materials Science and Engineering A 412, (2005) 171-176

Materials review, 43(3) (1988) 17-19
Jiangsu University of Science and Technology, 37(1) (2012) 25-26,29
Journal of Materials Processing Technology, 211 (2011) 1804- 1809 [7] Pouranvari M, Ekrami A, Kokabi AH.
Materials and Design 31 (2010) 2157-2162
Materials characterization on 60 (2009) 1289-1297

Introduction Flory founded the polymer gel bibulous theory in the 1950s, the super absorbent polymer was compounded in the 1960s, in the 1980s super absorbent polymer began to get application as a new type of functional polymeric materials.
Experiment Materials.
Ding: Polymer Materials Science and Engineering, Vol. 25 (2009) No. 5, pp.34-37.
Zeng, Journal of Guangdong College of Pharmacy, Vol. 21(2005) No.1, pp.4-6.
Wei: Super absorbent and water retention property material, (Chemical Engineering Publications, China 2005)

Materials and methods In the paper, the powder of UHMWPE (GUR–2122 by Ticona) with molecular weight of 4.0 million and its composites with various weight fraction of HA (C10(PO4)6(OH)2) microparticles were used (5, 10, 20 and 40 wt.%).
Wear resistance of test materials under dry sliding and lubrication (distilled water and plasma blood under environmental temperature at »37°C) were determined by “block-on-ring” scheme at load of 160 N and revolution rate 100 rpm in accordance with ASTM G99 and DIN 50324 with the use of SMT–1 machine.
Tervoort, Abrasive wear of Ultra-high molecular weight polyethylene, Encyclopedia of Materials: Science and Technology (2006) 1-8
A comparative investigation of the friction and wear behavior of polyimide composites under dry sliding and water-lubricated condition, Materials Science and Engineering - 2003, A356, 48-53
Sonjaitham, et al., Wear resistant ultra-high molecular weight polyethylene based nano- and microcomposites for implants, Journal of Nanotechnology, Vol. 2012, 7 pages.

Materials and Experimental Procedures Materials.
The single fibre pull-out tests were conducted by using a testing machine for micro material (MMT-11N Shimadzu Co., Japan, Load capacity: 2.5N).
Generally, the sizing agent of carbon fibre, which is assumed to be epoxy-based resin, serves as an insulating material in electroplating.
Chan: Polymer nanocomposites based on functionalized carbon nanotubes, Progress in Polymer Science, Vol. 35, (2010), pp. 837-867
Morita: Effect of Carbon Nanotubes Deposition Form on Carbon Fiber and Polyamide Resin Interfacial Strength, Journal of the Society of Materials Science, Japan, Vol. 65, No. 8 (2016), pp. 586-591.