Search results

In practical terms, this can lead to significant reduction of strength and performance properties of the material. 
Influence of environmental temperature and moisture content of aggregates on the workability of cement mortar Original Research Article, Construction and Building Materials, Volume 23, Issue 5, May 2009
Construction Materials. 2011
Integratsiya, partnerstvo i innovatsisii v stroitelnoy nauke i obrazovanii: nauchnoye izdaniye [Integration, partnership and innovation in construction science and education: scientific edition].
Journal of Power Sources. 01/2010.

Lee 1,b 1 Joining Research Group, POSCO Technical Research Laboratories Goedong-dong, Nam-gu, Pohang, Gyeongbuk 790-785, Korea 2 Recently joined at High Temperature Materials Research Group, Korea Institute of Materials Science, 531 Changwondaero, Changwon, Gyeongnam 641-831, Korea a hnk@kims.re.kr, bjongblee@posco.co.kr Keywords: API 5L X60; Electric resistance welding; Hydrogen induced cracking; Optimization; Segregation; Penetrator; Bondline Abstract.
Additionally, the materials for the small diameter ERW pipes tend to be from slit coils (double width coils) instead of full width coils, for the purpose of cost saving.
Experimental Procedure The material used in this study was API 5L X60 class hot coil (double width coil) with 6~10mm thickness for sour service line pipe.
Table 1 shows the chemical composition and typical properties of the parent material.
Sato: The Welding Journal, Research Supplement, June, (1981), p.104s.

Dissolving the row materials with deionized water respectively, and mixing them together slowly, then pouring into the reactor.
The composite material, LiFePO4 coated with carbon layer, was gained.
Combined the above data, it can be concluded that doping Mg 2+ in pure LiFePO4 materials have little effect on the low rate capacity, but can improve the high rate capacity and cycle life significantly.
The Li1-2xMgxFePO4 materials can be gained via hydrothermal route.
Tang: The Chinese Journal of Nonferrous Metals Vol. 15(9) (2005), p.1416-1420

However, during machining, soda lime glass is considered as a difficult-to-machine material as it is susceptible to brittle failure [2].
Others found that DRM of brittle materials produced continuous or curled chips which were unsegmented [6].
Hashemi, in: Foundations of Materials Science and Engineering, McGraw-Hill, (2004)
San: Ultraprecision ductile mode machining of glass by micromilling process, Journal of Manufacturing Processes, Vol. 13(1) (2011), p. 50-59
Zhong: Ductile or Partial Ductile Mode Machining of Brittle Materials, PhD thesis, School of MPE, Nanyang Technological University, Singapore, (2003)

Experimental Procedure Raw Materials.
Raw materials were melted in a clay graphite crucible using an electric resistance furnace.
Zhu, The effect of Y on the hot-tearing resistance of Al-5 wt.% Cu based alloy, Materials and Design 31 (2010) 2483-2487
Niroumand, Study of hot tearing of A206 aluminum alloy using Instrumented Constrained T-shaped Casting method, Materials Characterization 61 (2010) 318-324
Beckermann, Development of hot tear indicator for steel castings, Materials Science and Engineering A 413-414 (2005) 30-36

The accepted standard usage of hygroscopic material is 1g/L.
Experimental Materials.
Acknowledgement This work was financially supported by Nation Natural Science Foundation of China (No.51102214) and the Funds for the Protection of Cultural Heritage in Zhejiang Province (No.2011-202).
Mu, A new way to tune relative humidity: by saturated ionic liquid aqueous solutions, New Journal of Chemistry, (2013)
Peng, Preparation for Humidity Control Composite Paperboard and their Humidity Control Properties, Applied Mechanics and Materials, 310 (2013) 71-75

As a structural material, it has high specific strength and stiffness, excellent plasticity, which is applied in many industry areas.
Experiments Material and plating bath preparation. 2A12 aluminum plate was applied as the substrate metal, which is machined as the dimension of 30mm×30mm×2mm.
References [1] Alirezaei S, Monirvaghefi S M and Salehi M: Wear, Vol.262(2007), p. 978-985 [2] Teng Min, Li Yao and He Xiaodong: Aerospace Materials & Technology, Vol.3(2004), p. 14-19 [3] M.Q.
Yi: Journal of Functional Materials, Vol.31(2000), p. 337-340 [4] Xiaoting Huang, Gangyi Cai: Applied Mechanics and Materials, Vol.26-28(2010), p.843-846 [5] Palaniappa M and Seshadri S K: Materials Science and Engineering, Vol.460(2007), p. 638-644 [6] Li Ning: Practical technology of Electroless Plating (Chemical industry press, Beijing 2004).

In addition, the manufacturing industry primarily views recycling from a material perspective, while assembly plants using plastic parts focus on maintaining the quality of products made from secondary materials, as customer expectations remain high [4].
Apart from these factors, which often have a strong emotional and economical charge, a very complex field of polymer materials science unfolds in the mapping of this problem, the main pillars of which are polymer blends, filled polymer systems, physical and mechanical property modifications with additives, reinforcing materials or technologies (e.g., multi-component molding, foaming) [5].
This plastic belongs to the group of high-performance engineering materials and exhibits mechanical properties similar to those of polyamide 12 (PA 12).
Materials and methods 2.1.
Smaardijk and Erik Drent, Polyketones: Aliphatic, Encyclopedia of Materials: Science and Technology, K.

Thus development of effective as well as advanced uses of wood-based materials have attracted rising attention to achieve sustainable development of a society has been built by underground resources.
Advanced wood based materials technology group in AIST, found an interesting deformation behavior which leads to development of a novel shape-forming of solid woods [1-5].
Materials and Methods Wood.
References [1] Tsunehisa Miki, Osamu Yamashita, Hiroyuki Sugimoto, Kozo Kanayama: Proceedings of the 8th International Conference of Eco-Materials, 1 (2007), p.177
[16] Md Iftekhar Shams, Hiroyuki Yano and Keijirou Endou: Journal of Wood Science, 50 (2004), p. 337.

The nominal yield strength Fy = 345 MPa was assigned to the steel material for the columns and struts.
That value was reduced by 5% in the first tier to simulate possible variations in material properties.
ACKNOWLEDGEMENTS Financial support for this research was provided by the Natural Sciences and Engineering Research Council (NSERC) of Canada.
[2] Mahin SA, Shing PB, Thewalt CR, Hanson RD, “Pseudodynamic Test Method – Current status and Future Trends,” Journal of Structural Engineering, 115(8): 2113-2128, 1989
[5] Bonelli A, Bursi OS, “Predictor-corrector procedures for pseudo-dynamic tests,” International Journal of Computerized Aided Engineering Software, 22(7): 783–834, 2005