Search results

Influence of auxiliary abrasive on the resin bond used in diamond tools Tao Lin a, Shi Lei Li, Hui Ping Shao, Zhi Wang and Xin Bo He Institute for Advanced Material & Technology, University of Science and Technology Beijing, Beijing 100083, China aemail: lintao@ustb.edu.cn Keywords: diamond tools; auxiliary abrasive; hardness; bending strength Abstract.
Diamond Tools, 3-4(2002), p12 [5] X F Liu, Y Z Li, The microanalysis of bonding condition between coated diamond and matrix, International Journal of Refractory Metals & Hard Materials, 21(2003), p119 [6] Min Ho Choi, HoYun Byun.

Design and calibration of a six-axis force sensor for docking mechanism Sheng Lin1,2, a, Lingxuan Zhang2,b, Jiming Shao2,b, Chongfeng Zhang2,b 1School of Mechanical Engineering, Dalian Jiaotong University, Dalian 116028, China 2Key Laboratory of Science and Technology for National Defence on Structure and Mechanism Technology, Shanghai 201108, China alinsheng138@163.com, b40337764@qq.com Keywords: Six-axis force sensor, Calibration machine, dynamic character.
The material of the docking ring is aluminum alloy, whose density is; the modulus of elasticity is 70GPa; the Poisson's ratio is 0.33.
Quartz crystal material density is; the modulus of elasticity is 90GPa; the Poisson's ratio is 0.25.
Fig.7 Structure of calibration arm To verify the influence of calibration arm deformation on the calibration result, finite element analysis is conducted on the calibration arm in ANSYS software. 65Mn is selected as the material of the arm, whose elastic modulus is 200GPa, and Poisson's ratio is 0.3. 1250N, 1250N and 2500N are applied along X-axis, Y-axis and Z-axis on the calibration arm.
Kerr, Analysis, Journal of Mechanisms Transmissions and Automation in Design–Transactions of the ASME 111(1989)

For the modeⅡcrack, the integral loop same with modeⅠ, in this case we have (17) (18) Then, the equation (7) becomes (19) so maximum energy release rate for crack extension is given by (20) Fig.3 A typical image of crack branching mode I crack Conclusions The integral reported here is an accurate, reliable for the calculation of the intensity of singular stress distribution in plane, isotropic elastic material problems.
[5] B Budiansky and J R Rice．Conservation Laws and Energy-release Rates．Journal of Applied Mechanics，(1973) No.40,p.201-203
J. of Materials Science,(1986) No.21, p.717-724

Relevant parameters about vacuum chamber Dimensions of chamber[L x W x H] Dimensions of ribbed plate[H x W] Material parameters[3]（16MnR） yield point modulus of elasticity E[GPa] 206 poisson ratio 0.3 Static analysis of vacuum chamber According to the characteristics of 3D model and structural features, there choose solid element type Solid92, utilize equilibrium of forces and the boundary conditions of structure, then connect the elements in accordance with the original structure to form whole finite element equation shown below[4]
Optimization and static analysis on structure of the vacuum chamber There are various options on the optimization of a chamber when it is designed, for example, choosing a material with high stiffness, increasing the chamber’s thickness or the number of ribs, etc.
Taking the conditions of practical production into account, replacement of better material or increase the thickness of chambers can have a significant raise in facility cost.
[4] Chang Yuan, Wancai Zhen: Journal of China's Electronic Science Research Institute Vol.2(2007), p.162-164,in Chinese

Piezoelectric materials such as aluminium nitride (AlN) and zinc oxide (ZnO) are mainly used in the FBAR.
Ru is used as the electrode material for FBAR in K-band frequency due to its higher acoustic impedance than other electrode materials [1].
The disagreement on the suppression is due to material loss from the piezoelectric material and electrodes.
Yoshino, Piezoelectric thin films and their applications for electronics, Journal of Applied Physics, 105 (2009) pp.061623-7
Ruimi, et al., Effect of geometry on the performance of MEMS aluminum nitride trampoline resonators in longitudinal resonance, Journal of the Franklin Institute, (2011)

Introduction Using waste materials in the construction industry becomes one of the opportunities for material recycling.
Experimental Program Materials and Mixture Proportion.
The mixing started from dry cementitious materials (FFA and GGBFS) for 30 seconds using the handheld concrete mixer at a lower speed for 30 seconds.
Afterward, hand mixing was performed for 60 seconds to scrape down the materials collected on the container side.
[6] Salim M U and Mosaberpanah M A, “The mechanism of alkali-aggregate reaction in concrete/mortar and its mitigation by using geopolymer materials and mineral admixtures: a comprehensive review,” European Journal of Environmental and Civil Engineering, 26, no. 14, pp. 6766–6806, Aug. 2021, doi: 10.1080/19648189.2021.1960899

Introduction Nano-sized manganese oxides are the one of most important attracted considerable interest materials in various industries, such as rechargeable lithium batteries, electrochemical supercapacitors, electronics, catalysis, and sensors.
The prepared δ-MnO2 material exhibits high capacitance value and good cycling behavior.
Experimental Materials and Synthesis.
Favier, Structural in situ study of the thermal behavior of manganese dioxide materials: toward selected electrode materials for supercapacitors, ACS.
Reddy, Synthesis and electrochemical characterization of amorphous MnO2 electrochemical capacitor electrode material, Journal of Power Sources. 132 (2004) 315–320

Strength properties of the material decrease with increasing of annealing temperature whereas, on the contrary, plastic properties increase.
Experiment The initial material was in the form of pickled cuts of the hot rolled strip with thickness of 3.9 mm.
It is possible to say that up to a value of deformation degree ε = 30 % virtually no recrystallization occurs and the material undergoes work hardening.
Journal of Material Science, 26, 1991, No. 19, p. 5158-5162
[4] Information on http://www.fmmi.vsb.cz/model [5] Deformation Behaviour and Properties of Selected Metallic Materials.

For the sand, the material type 147 was used.
This is an isotropic material model with damage.
The balsa has been considered as orthotropic material.
The authors also acknowledge support of the Institute of Thermomechanics AS CR, v.v.i. of the Czech Academy of Sciences through the project No.
Covey, Blast and Fragment Injuries of the Musculoskeletal System, The Journal of Bone and Joint Surgery 84 (2002) 1221-1234

Methodology Materials.
The materials used consisting of clinker, gypsum, and the additional materials consist of lime stone, and pozzoland.
CIRP Journal of Manufacturing Science and Technology 2010; 2(3):144–52
Uses of alternative fuels and raw materials in the cement industry as sustainable waste management options.
Construction and Building Materials 2009; 23:1954-1959