Search results

Applied Surface Science 256 (2010) 6775–6781 [5] W.H.
Materials for Mechanical Engineering ,2004,28(12):46-48 [8] F.
Wang, Application of ultrasonic technique in the processing and synthesis of inorganic materials , J.
Journal of the chinese ceramic society 0454 - 5648 (2002) 05 - 0615 - 05 [9] S.K.
Corrosion Science 47 (2005) 3202–3215

Journal Citation (to be inserted by the publisher) Copyright by Trans Tech Publications Effect of Compaction Pressure on the Microstructure Evolution of Anode Substrate for SOFC Application Sang-Woo Kim, Jong-Ho Lee, Hue-sup Song, Joo-sun Kim and Hae-Weon Lee* Nano-Materials Research Center, Korea Institute of Science and Technology, 39-1 Seongbuk, Seoul 136-791 Korea, hwlee@kist.re.kr Keywords: Solid Oxide Fuel Cell, Anode, Ni/YSZ Cermet, Conductivity Abstract.
Phase analysis was carried out with XRD (Mac-Science, Japan) to identify the phase changes of composite before and after the heat treatment.
The porosity and gas permeability of the samples were also measured with mercury porosimeter (Poresizer 9320, Micrometrics Inc., USA) and perm porometer (Porous Materials Inc., USA), respectively.
Acknowledgment This work was partially supported by the National Research Laboratory Program of the Ministry of Science and Technology in Korea.

Fig. 2 shows the theoretical transmission curve of the near-infrared high-pass film which was designed by the principle of interference edge filter [9] using the coating materials of TiO2/SiO2.
Leaving the required near-infrared high-pass film at the special place, the substrate was then put into a suitable solvent to remove the protect photoresist and the coating materials which was deposited on its surface after all layers of thin film were coated.
Acknowledgments This work was supported by National Natural Science Foundation of China (No. 61204125) References: [1] G.
Wolf, Oxygen plasma removal of thin polymer films, Polymer Engineering and Science, 20(1980) 1087- 1092
Noh, Effect of atmospheric-plasma treatments for enhancing adhesion of Au on parylene-c-coated protein chips, Journal of the Korean Physical Society, 44 (2004) 1177-1181.

Yi: δ-TRIP Steel - Pohang : Pohang University of Science and Technology, 2010
Yi: Materials Science and Technology.
Metallurgical and Materials Transactions A, Vol. 23 (1992), p. 3085
Pohang: Pohang University of Science and Technology, 2011 [14] E.S.B.
Journal of Iron Steel Research, Vol. 23 (2016), p. 988.

Fibre Processing.The P(LL-co-CL) copolymers weremelt-spun into monofilament fibres using a small-scale melt-spinning apparatus which was capable of processing as little as 10 g of material.
Understanding the combination of the two and how they relate to properties is the key to the successful development of a new material.
Acknowledgements The authors wish to thank the Department of Chemistry, Faculty of Science, Chiang Mai University for providing the facilities used in this research and the National Metal and Materials Technology Center (MTEC), Thailand, and the National Research University Project under Thailand's Office of the Higher Education Commission for financial support.
Rypa´cek: European Polymer Journal Vol. 42 (2006), p. 888 [4].
Hilborn: Polymer Science Vol. 32 (2007), p.455 [6].

The Progress of Mineral Processing Technology of Lead-zinc Mine in China Yu Chen1,2,a, Shuming Wen1,2,b*, Yijie Wang1,2,c, Qicheng Feng 1,2,d, Jinlin Li1,2,e, Chuanfa Cui 1,2,f 1State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093, China 2Faculty of Land Resource Engineering, Kunming University of Science and Technology, Kunming 650093, China amjzchenyu@126.com, bshmwen@126.com (Corresponding Author), cyjwang2012@126.com, dfqckmust@126.com, e396613803@qq.com, fccf99999@126.com Keywords: Lead-zinc Mine, Technological Process, Flotation Reagents, Progress Abstract.
Lead and zinc are indispensable metallic materials for the national economy.
A variety of lead-zinc materials were effectively recovered.
[4] Q.Liu, Y.C.Zhao, D.Guo: A Novel Process for Preparation of Zinc and Lead Concentrates by Lean Ores Bearing Zinc and Lead[J], Journal of University of South China(Science and Technology), 2010, 24(2):29-33

Materials and specimen fabrication Concrete was prepared using type 42.5R ordinary Portland cement, water, crushed limestone, sand, glass fibers and adscititious dose.
The materials used conformed to relevant steel fiber reinforced concrete standard specifications.
Acknowledgements This research program is supported by the Province Natural Science Foundation of Yunnan (Grant No. 2007A0015Z).
Beijing:Science Press, 2003 [3] WANG Shi-yue, ZHANG Li-xiang, XU Ren-ping et al.
Journal of Henan Agricultural University, 2009, 43(4): 405-409 [5] Gumble EJ.

Hou, Solar-powered airplanes: A historical perspective and future challenges, Progress in Aerospace Sciences, 71 (2014) 36–53
Ekaterinaris, Design, performance evaluation and optimization of a UAV, Aerospace Science and Technology, 29 (2013) 339-350
Smith, The development of a Small Solar Powered Electric Unmanned Aerial Vehicle Systems, Applied Mechanics and Materials, 465-466 (2014) 345-351
Shaholia, Sizing and preliminary hardware testing of solar powered UAV, The Egyptian Journal of Remote Sensing and Space Sciences, 16 (2015) 189-198
Smith, Review of Solar and Battery Power System Development for Solar-Powered Electric Unmanned Aerial Vehicles, Advanced Materials Research, 1125 (2015) 641-647

Defects have a crucial role in altering material properties.
Therefore, the study of defect control in material fabrication is important [1].
Acknowledgment The authors would like to thank the Faculty of Mathematics and Natural Sciences, Universitas Gadjah Mada for the research facilities through research grant No. 60/J0LL28/PI,.06.02/2022.
Markevich, et al., Tin-vacancy complex in germanium, Journal of Applied Physics 109, 083705 (2011)
Vanpocuke, et al., Revisiting the neutral C-vacancy in diamond: Localization of electrons through DFT plus U, Diamond and Related Materials 79 (2017) 60-69

Introduction Increasing the efficiency of modern gas turbines involves the design of new nickel base superalloys to provide improved high temperature creep resistance through the precipitation of a strengthening γ' phase, which undermines the corrosion resistance of these materials.
Streiff: Journal de Physique IV.
Rhys-Jones: Corrosion Science Vol. 29 (1989), p. 623
Datta et al, Environmental Effects on High Technology Materials (Proc.
Polish-Japanese Symposium, Polish Academy of Science, Zakopane (1997), p. 81