Search results

Introduction Epoxy resin was widely used in all kinds of packaging materials, coatings, civil engineering, adhesives and composites.
Experimental Materials.
Samples of 11cm long, 4mm thick were cut by a dumbbell-shaped mold with the sample Preparation Machine jin jian XYZ-12(made in China).The mechanical properties were tested using a Universial Materials Testing Machine jin jian XWW-20 (made in China), operating at a crosshead speed of 5mm/min for testing (GB1040.1-2006 China standard).
[2] Z.J.Zhang,X.J.Mei,L.R.Feng, Preparation and characterization of Melamine polyphosphate as a Flame Retardant, Chinese Journal of applied Chemistry.20(2003) 1035-1038
[8] X.Y.Li, Z.Z.Wang, H.J.Liang, Flame Retardation of EVA Copolymer using Melamine phosphate and pentaerythritol as Intumescent Flame Retardants, Polymer Materials Science and Engineering. 23(2007) 145-148.

Wu2,d 1School of Materials Science & Engineering, 2Henan University of Science & Technology, 471003, China aslzhao@mail.haust.edu.cn, bjine0736@163.com, cwenjiuba@mail.haust.edu.cn, dcwuzhaoyang870203@126.com Key words: sol-gel; spin-coating; NiO thin film; electrochemistry.
Nickel oxide shows great advantages as one of new and efficient anode materials of thin film lithium ion battery for its higher specific capacity than carbon anode and its higher melting point than the metal lithium which will be damaged during the reflow solder process[2].
When the nano-NiO thin films are used as a anode material in lithium battery, advantages will assure a higher reversible capacity, reversible capacity, long cycle life when increase the current density of charge-discharge.
Inamdar: Journal of Alloys and Compounds Vol. 489 (2010), p. 667 [5] M.
Ji: Functional Materials Vol. 33 (2002), p. 298 [8] W.E.

Influence of [Si], [Ti] Content on Fluidity of Hot Metal Yuanyuan He1,a, Qingcai Liu1,b, Jian Yang1, Bineng Yang2, Minghua Long2, Huimin Zheng1, Chengwei Liu1, Min Wei1 1College of Materials Science and Engineering, Chongqing University, Chongqing, 400030, China 2Shougang Shuicheng Iron & Steel Corporation，Liupanshui, 553000,China aheyuanyuan119@163.com, bliuqc@cqu.edu.cn Keywords: Hot Metal, Titanium, Viscosity, Liquidity, Solubility.
Experimental Materials.
Du: Journal of Shenyang University of Technology.
Metallurgical and Materials Transactions B.
Metallurgical and Materials Transactions B, Vol.29B(1998), p.371

Material of steel tube was SS400 (Japanese Industrial standard: JIS).
Material Model for Simulation Concrete.
Material parameters for steel tube and reinforcements are used from material properties.
Du: Application of ADINA in nonlinear analysis of reinforced concrete structure, Science Technology and Engineering, Vol.14(2006), p.78-81
Hasegawa: A study on axial compressive behaviors of reinforced concrete filled tubular steel columns, Journal of Constructional Steel Research, JCSR, Vol. 76(2012), p. 144-154

The defined material properties were summary shown in Fig. 7, according with [9].
Materials propoerties applied for the analyzed human ankle joint virtual model Detailed informations regarding the material properties for component groups are defined in Table 1.
Ulster Medical Society Journal, 64–72. (2005) [7] CONTEMPLAS Motion Analysis Equipment user manual. 2010
New Trends in Mechanism Science.
Mechanisms and Machine Science, vol 5.

Tongsri 2, d 1 Division of Materials Technology, Faculty of Energy, Environment, and Materials, King Mongkut's University of Technology Thonburi, Bangkok 10140,Thailand 2 National Metal and Materials Technology Center, Pathum Thani 12120, Thailand a r_biwja@hotmail.com, bnandh.tha@kmutt.ac.th, cnuchthana.poo@kmutt.ac.th,d ruangdt@mtec.or.th Keywords: Copper powder extrusion, Feedstock, Pseudo-plastic, Debinding, Sintered properties Abstract.
Acknowledgements This work was funded by the National Metal and Materials Technology Center (MTEC), Thailand, and supported by King Mongkut's University of Technology Thonburi.
German: Powder Metallurgy Science (MPIF, New Jersey 1994)
[6] C.Karatas and S.Saritas: Journal of Turkish Engineering and Environmental Sciences of TUBITAK.

Yu 1,d 1 Department of Materials, University of Science and Technology Beijing, China 2 State Key Laboratory of Advanced Metals and Materials, University of Science and Technology Beijing, China a wmmao@mater.ustb.edu.cn, blchen@mater.ustb.edu.cn, cyangp@mater.ustb.edu.cn, d yuyongn@sina.com Keywords: polycrystalline metal, plastic deformation, stress, strain, texture, simulation.
Kalidindi: International Journal of Plasticity, Vol. 18 (2002), p. 359 [5] R.
Yu: Chinese Science Bulletin Vol. 48 (2003), p. 204 [9] W.
Mao: Crystallographic texture and anisotropy in metal materials (Science Press, Beijing, 2002)
Material Science and Technology Vol. 18 (2002), p. 443 [13] W.

Material property parameter.
Material property parameter.
He: Journal of Yangzhou Polytechnic College.
Jin: Journal of Hydraulic Engineering.
Fre′de′ric: Construction and Building Materials.

However, no significant improvement of power factor is obtained in these bottom-up prepared nanomaterials when comparing with the bulk Bi2Te3 materials [2].
Dyck, Clemens Burda, Toward high-performance nanostructured thermoelectric materials: the progress of bottom-up solution chemistry approaches, J.
Elsasser, Nanostructure, Excitations, and Thermoelectric Properties of Bi2Te3-Based Nanomaterials, Journal of Electroni Materials. 41(2012) 1792–1798
Tu, Aqueous chemical reduction synthesis of Bi2Te3 nanowires with surfactant assistance, Materials Letters. 60 (2006) 2534–2537
[8] Yanhua Zhang, Guiying Xu, Pan Ren, Ze Wang, Changchun Ge, Effects of Various Reductants and Surfactants on the Nanostructure of Bi2Te3 Synthesized by a Hydrothermal Process, Journal of Electronic Materials. 40 (2011) 835–839

Various researchers studied tribological damages of PEEK or PEEK composite materials for mechanical parts [4-6].
Materials of the bearing’s ball and retainer were Alumina and PTFE composite (PTFE and carbon graphite), respectively.
[15] Ali Yousefpour, Mehdi Hojjati, Jean-Pierre Immarigeon, Fusion Bonding/Welding of Thermoplastic Composites, Journal of Thermoplastic Composite Materials, SAGE, 17, (2004), 303-341
Polymer Engineering and Science 31, (1991), 526-532
Kida, Observation of Tribological Wear on PEEK Shaft with Artificial Defect under Radial Rolling Sliding Point Contact, Key Engineering Materials, 858, (2020), 95-100