Search results

Using insulation slurry as printing material, the cathode insulation layer was formed on the cathode glass plate.
Key engineering materials.
Applied surface science.
Diamond and related materials.
Microelectronics journal.

Materials and methods Physicochemical parameters were determined in situ.
Advanced Materials Research.
Geomicrobiology Journal 24(2): 111-123
Advanced Material Research.
Proceedings of the National Academy of Sciences of the United States of America 104(27): 11436-11440

Journal Citation (to be inserted by the publisher ) Copyright by Trans Tech Publications Water-Lubrication Effects on Zirconia Debris Production in Hip-joint Simulators P.A.
Ben-Nissan 3 1 Peterson Tribology Lab, Department of Orthopaedic Surgery, Loma Linda University Medical Center, Loma Linda, California USA, pwilliams@som.llu.edu 2 Department of Materials, Kyoto Institute of Technology, Kyoto, Japan 3 Department of Chemistry, Materials, and Forensic Science, University of Technology, Sydney, Australia Keywords: Zirconia, water lubrication, serum lubrication, wear surface, wear debris, clinical Abstract.
The debris size and surface features in the wear zone of the femoral ball indicated delamination consistent with catastrophic failure of the material.
Cales, B., Zirconia as a sliding material: histologic, laboratory, and clinical data.

Figure 1 The structure size of three Fig. 2 Corrugated radius are reduced corrugated sealing ring (unit mm) by 0.1mm structure (unit mm) Fig. 3 Corrugated radius are increased by 0.1mm structure (unit: mm) We choose nickel-based superalloy GH4169 as the material of sealing ring, working temperature can reach to 600 ℃.
Table 1 material mechanics parameter property Temperature/℃ Tensile strength/MPa Yield strength /MPa modulus /GPa Thermal conductivity Coefficient of linear expansion Poisson's ratio 20 1270 1030 203 ／ ／ 0.321 650 1055 865 142 21.2 14.8 0.361 2 The finite element calculation of metallic sealing ring 2.1 The simplified finite element model of metallic sealing ring Because the structure and stress of sealing ring are symmetry, therefore in the process of calculation, the followings are used to equivalent or simplify the model: without considering material defects, material is isotropic, without considering the influence of residual resistance friction force and the thickness on the contact surface between the model, set to the axisymmetric model.
References [1] Chi Libo.The mechanical sealing design of high pressure metal bellows[J]．Journal of Machinery, 2001，28(Supp1)：157—158
[7] Aircraft engine design with material data sheet (4 copies).
Advances in aeronautical science and engineering ,2012.08, Volume three.

Materials of the sensor were Pt and Pt/Rh [2].
NASA used semiconductor materials - Al:ZnO and N:ITO to make thin film heat flux sensor.
Acknowledgements The authors are grateful to the National Natural Science Foundation of China (Grant Nos.: 50976006, 11102005), Program for New Century Excellent Talents in University (Grant No.: NCET-10-0006) and Specialized Research Fund for the Doctoral Program of Higher Education (Grant No.: 20121103110009) for the financial support.
Advanced Materials Research, 2013, 718-720:1181-1184
Journal of Spacecraft and Rockets, 1997, 34(6): 792-798

Effects of Incident Angle on Microstructure of Ni-Cr Film Deposited by PVD Shan Yingchun1,a, Xu Jiujun1,b, He Xiaodong2,c and Li Mingwei2,3,d 1Electromechanics and Materials Engineering College, Dalian Maritime University, Dalian 116026, China 2Center for Composite Materials, Harbin Institute of Technology, Harbin 150001, China 3ChengDu Aircraft Design & Research Institute, Chengdu 610041, China ashanychun@126.com, bjjxu@dlmu.edu.cn, chexd@hit.edu.cn, dlimingwei@hit.edu.cn Keywords: KMC simulation; Ni-Cr film; Incident angle Abstract.
Daw, in: Proceedings of the 1986 ASM Materials Science Seminar, edtied by R.J.
Li: Chinese Journal of Aeronautics Vol. 19 (2006), p.

Prediction and Prevention of Distortion for the Thin-walled Aluminum Investment Casting Yongzhen Liu1, Guoming Cui1,2, Jianmin Zeng1, a and Wukui Gan3, Jinbo Lu3 1Key Lab. of Nonferrous Materials and New Processing Technology, Guangxi University, Nanning 530004, China 2Henan Mechanical and Electrical Engineering College, Xinxiang 453002, China HONGDU Aviation Industry Group LTD., Nanchang 330000, China azjmg@gxu.edu.cn Keywords: casting stress; Investment casting; thin-walled casting; distortion Abstract.
Acknowledgements This study is financially supported by Chinese 973 project (2012CB722804 ) and Guangxi Natural Science Foundation (2011GXNSFF018001).
[3] Yuichi Motoyama, Yuki Inoue, Gota Saito, Makoto Yoshida: Journal of Materials Processing Technology  Vol. 213( 2013), p. 2270 [4] M.T.
David: Applied Thermal Engineering  Vol. 44 (2012), p. 100 [6] Jianmin Zeng, Jie Liang, Zhiliu Hu: Advanced Materials Research Vols. 399-401 (2012) , p.13 [7] Information on http://www.simtec-inc.com

This process allows to machine high strength and wear-resistance material such as hip implant material.
Goswami, Review of wear mechanisms in hip implants: Paper I – General, Materials & Design, 25, (2004) 385-393
Jin, The effect of aspherical geometry and surface texturing on the elastohydrodynamic lubrication of metal-on-metal hip prostheses under physiological loading and motions, Journal of Mechanical Engineering Science, 224, (2010) 2627-2636
Baharom, Investigation of Workpiece Positioning Methods for Machining Oil-Pocket on Hip-Implant Spherical Surface, Key Engineering Materials, 594-595, (2013) 535-539

The material of the main structure of the derrick is Q235 steel, and the yield point is about 235MPa.
Materials Constitutive equation for thermal strain in the mushy zone during solidification of aluminium alloys[J].
Science Forum, 2006
Applied Mechanics and Materials, 2011
Journal of Applied Physics, 2012 (8)

Machining Error and Milling Process Control Methods for Joint Surface of Machine Tool Bin Jianga, Kai Zhang b, Lin Yangc, Minghui Zhang, Shengjie Wang Machinery Industry Key Laboratory of Chip Control and High Efficiency Tool Technology, Harbin University of Science and Technology, 52 Xuefu Road, Harbin, 150080, China a13903611465@163.com, bzhangkai198835@126.com, c15004501851@163.com Keyword: Machine tool, Joint surface, Machining error, Milling process Abstract.
Shin: Journal of Dynamic Systems Measurement and Control Vol. 122 (2010), p. 95
Gong: Advanced Materials Research Vol. 630 (2013), p. 463
Wang: Advanced Materials Research Vol. 188 (2011), p. 515
Sun: Advanced Materials Research Vol. 591 (2012), p. 409.