Search results

Fig.18 Welds' connection collapse of crossing board Fig.19 Floor warpage deformations of support joint Fig.20 Anchor bolt of support joint sheared Fig.21 Bars bending deformations Frame Structure Masonry materials of frame structure were small hollow blocks.
The main reason was that the material characteristics of bolt-sphere joints, crossing boards, little-columns and purlins were different.
Acknowledgements This work was financially supported by the National Natural Science Foundation Program (51278469, 50878137), the Special Fund for the Basic Scientific Research Business of the Institute of Crustal Dynamics, China Earthquake Bureau (ZDJ2009-03), the Special Program for Science Field Investigation on Lushan Ms 7.0 Earthquake from the China Earthquake Administration (2013), and the Key Project Foundation of Shanxi Province (20080321086).
Journal of Building Structures, 1991, 5:43-47.
Advanced Science Letters, Vol.4, P2654–2665.

The most common injection material is mixture of cement and waters in practice though many injection materials available in the market.
Seismic Assessment and Rehabilitation of Existing Buildings (NATO Science Series: IV: Earth and Environmental Sciences), Kluwer Academic Publishers, Dortrecht, 2003
[14] ASCE (Committee on Grouting of the Geotechnical Engineering Division), Preliminary Glossary of Terms Relating to Grouting, Journal of the Geotechnical Engineering Division, ASCE, 106(GT7) Proc.
Akyol, Strengthening foundations of seismically weak buildings on sandy soils in Denizli, Turkey, Environmental Earth Sciences, 66(5) (2012) 1415-1421

The maximum stress of tooth root which has the larger moment is smaller than 100Mpa and is far smaller than the material yield limit.
Its value far exceeds the yield limit of material and the components enter the stage of plastic deformation.
Acknowledgement It is a project supported by Natural Science Foundation Committee of China (51075049).
Mmaclennan: Journal of Mechanical Engineering Science Vol.216(2002), P.1005-1016
Mechanical Engineering Science, 3 (2004) 131-142.

The captured materials on the wall can be conductive to be tossed again to enter the inner rotation under the impact of eccentric vertical circulation, which can finally create hopper back-mixing that can decrease the separation efficiency and make the inner rotation even more disorder.
The largest sub-speed is the tangential velocity with the biggest magnitude in the power material separation process.
Dust collecting equipment: (Shanghai Science and Technology Press, China 1983)
Numerical Simulation on Gas Flow Field of Cyclone Separator: (Journal of Beijing University of Technology)
Numerical Calculation and Experimental Research on Gas-solid Phase in Cyclone Separator: (Doctoral Thesis, Chinese Academy of Sciences, PP. 33-55, China 2003).

Materials and Methods Materials.
Acknowledgments This study was supported by the National Science Council (NSC) of Taiwan (Contract No.
G., and Huang, Y., Fire-Damage or Freeze-Thaw of Strengthening Concrete Members Using Ultra High Performance Concrete, Advanced Materials Research Vols. 79-82, p. 2047-2050 (2009)
[4] Bozkurt, N. and Yazicioglu, S., Strength and capillary water absorption of lightweight concrete under different curing conditions, Indian Journal of Engineering and Materials Sciences , Vol. 17, pp. 145-151 (2010)
Journal of Hazard Materials, Vol. 179 (1–3), pp. 954–65 (2010)

PANI composited conductive fabric features wide application, has developed from the general anti-static fields to the electromagnetic shielding (EMI), electronic intelligence, anti-bacterial deodorant, electrochromic, absorbing stealth materials and other special areas, the prospect of market is broad.
In this study, based on the experimental studies of single factor, the experiment of five-factor quadratic general rotation combination were designed to produce a good electrical conductivity of PANI composited conductive fabrics with nylon / spandex warp-knitted fabric of locknit stitch as matrix material, PANI as the conductive material and in-situ polymerization as the method, which is helpful for the further research of smart textiles.
Experimental Materials and Methods Experimental Materials.
Hu: Journal of Textile Research in China Vol.26 (2005), p. 10
Seong: Journal of Applied Polymer Science Vol. 81 (2000), p. 684

The Restriction of Hazardous Substances Directive (RoHS), which took effect on 1 July 2006, restricts the use of six hazardous materials including Pb in the manufacturing of electronics devices.
Thus, the drive to eliminate lead (Pb) from electronics has resulted in the replacement of Pb-free alloys for both surface finish and soldering materials in electronic devices.
However, as the electronics industry migrated toward Pb-free assembly and system, the surface finish materials have been replaced with pure Sn or Sn-based alloys.
Greene, "Microstructural Evolution during Film Growth," Journal Vacuum Science Technology, pp. 117-128, 2003
Li, "Optimum Thickness of Sn Film for Whisker Growth," Journal Electronic Materials, pp. 2069-2075, 2011.

What's more, as for the parallel steel truss component, the smaller the damping of its material is, the larger the vibrating amplitude is.
Journal of hot working process, 2013(7):198-199,203(In Chinese)
Mechanical Science And Technology, 2001,20(7):587-589(In Chinese)
Journal of materials research and applications, 2012, 6 (1): 14-20(In Chinese)
Comparative Study of the vibratory stress relief (VSR) and the thermal stress relief (TSR) of Cylinder wallboard[J].Advanced Materials Research ,Vol. 331 (2011) 460-464.

NPEs are synthetic detergents main raw materials, very extensive.
Qiao, etc’s research [21], the survey results of sludge samples from 4 wastewater treatment plants were all detected NP kind material, and the concentration range in 1~ 128 mg/kg for three consecutive years since 2003.
The sludge was placed under 5 kGY of 60Co-ray irradiation in 24 hours, the sludge easily degradable organic matter content of contaminants was in the increase, and refractory material was reduced.
Acknowledgements This work was financially supported by Center for Environmental Remediation, Institute of Geographic Sciences and Natural Resources Research, Chinese Academy of Sciences, Beijing Municipal Research Institute of Environmental Protection.
Xu, “Transport of PCBs in contaminated paddy fields”, Journal of environmental science, Vol. 21, No. 4, 454-458, 2001 [18] J.

On the other hand, when the materials passed through the small gap of between the planetary screws and the center screw bottom, they were suffered from much higher shear rates, squeezing and stretching action due to the periodic perturbation in the space and speed, thus the dispersion of the materials were improved.
The experimental materials and formulation were shown in Table 2 and Table 3.
Table 2 Experimental materials name type manufacturer active nanometer CaCO3 GCC-R Qingxin Shuang Rong Chemistry Co.
In summary, no obvious difference in dispersion of CaCO3 is found, but the material were suffered to the much stronger shear rates in the intermeshing zones of the twin-screw extruder, and larger ratio of the length to the diameter also increased the residence time of the materials.
[8] Xiaolong Wang, Baiping Xu, Yuejun Liu, Meigui Wang and Huiwen Yu: Polymer Materials Science & Engineering, Vol. 28-3 (2012), p. 171