Search results

Savvakin, in: Key Engineering Materials, Trans Tech Publ, 2000, pp. 55-62
Wicker, Microstructure and mechanical behavior of Ti–6Al–4V produced by rapid-layer manufacturing, for biomedical applications, Journal of the mechanical behavior of biomedical materials, 2 (2009) 20-32
Tajima, Microstructure and properties of titanium alloy produced in the newly developed blended elemental powder metallurgy process, Materials Science and Engineering: A, 213 (1996) 148-153
Cao, Consolidation/synthesis of materials by electric current activated/assisted sintering, Materials Science and Engineering: R: Reports, 63 (2009) 127-287
Furuta, Thermomechanical properties of P/M β titanium metal matrix composite, Materials Science and Engineering: A, 243 (1998) 273-278

However, there is still a lack of reliable biaxial testing data to verify failure initiation and propagation of composite materials, due to the difficulties and expense of conducting these tests.
Introduction Composite materials are commonly used in many industrial fields, especially in aerospace and wind energy.
Although this system has a high capacity to conduct most planar bi-axial tests for composite materials, it is complex and expensive.
The GFRP material lay-up is 1.2 mm through-thickness [0/90]2s cross-ply.
Li, "The background to the third world-wide failure exercise," Journal of Composite Materials, vol. 47, pp. 2417-2426, 2013

Materials and methods Experimental materials The experimental samples of LIP cigarette paper L1, L2, L3, L4, and ordinary cigarette paper C1 are provided by an American company; C2 is common sample from a Chinese cigarette paper mill.
Preparation of cigarette sample A batch of different specifications Chinese style cigarette samples (cigarette sample numbers and cigarette paper sample numbers keep consistent) were rolled with the same tobacco materials in Passim cigarette rolling machine.
Journal of Yunnan University, 2010, 32(S1): 110-114 [7] Hu Qun,Gu Bo,Ma Jing et.al.
Tobacco Science&Technology, 2002, (8): 7-10 [8] Hoffmann D., Hoffmann I.
Tobacco Science&Technology 2009, (2): 5-15

Structure–property relationship of dodecylbenzenesulfonic acid doped polyaniline Liu Yinga, Qi Wenb, Jiali Guanc, Shijie Zhaod, Qixing Hue, Zhifeng Houf, Qiaozhen Yu* Department of Materials and Textile Engineering, Jiaxing University, Jiaxing Zhejiang 314001, P.
Experimental Details Materials.
Materials Science and Engineering B 143 (2007) 31–37
Materials Chemistry and Physics 129 (2011) 666– 672
European Polymer Journal 43 (2007) 2331–2341.

Appearing as follows: 1) Materials are not in good positions and the space is not used wisely.
After being stored, the materials’ location on the record may be different from where they actually are due to some errors.
The departments of stocks, production, and sales cannot fully be in line with the storage management of the raw materials and the production.
In the storehouse, there are raw materials, products and in-made products.
The former one represents the manufacturer to order requested materials, and to take charge of the process of materials’ movement.

Testing materials and methods Testing materials The testing material was the hot rolled industrial high plastic stain ratio structural steel sheets, the hot-rolling take normal heating system, the final rolling temperature and coiling temperature were separately are 860˚{TTP}730 C± 20˚{TTP}730 C and 620˚{TTP}730 C ± 20˚{TTP}730 C.the hot rolled thickness was 4.0mm. and its chemical composition shown in table 1.
Journal of Wuhan Yejin University of Science and Technology, 1998,21(2):161-165.

Mansourb Laboratory of Electronic Materials Study for Medical Applications (LEMEAMED), Constantine University-Algeria.
It consists in a deposited deep detector material used as device for direct detection on the top of the ASIC [1].
Hydrogenated Amorphous Silicon Sensors based on Thin Film on ASIC technology IEEE Nuclear Science Symposium Conference Record , 2005, N35-55 , pp.1389- 1394
[5] H.M Branz, A Yelon and B Movaghar: ‘Physics of meyer-Nedel rule in amorphous silicon’, (Material research society symposium proceedings), Vol. 336 (1994), p. 159
Zhou Estimation of the Mobility-Lifetime products in Amorphous Silicon in the Presence of Dispersive Transport: Journal of Applied Physics Vol. 33 (1994), pp. 1655-1658.

U75V material rail is used to experiment, the number of cycles of rail roller is 106 ,and the speed of rail roller is about 160km/h,friction coefficient is 0.3.
(5) As all said above, equation (4) can reflect preferably the variation of rail wear when others factors such as materials, contact circumstance etc, are not be considered, but only the curve radius and axle load .It is feasible to forecast rail wear volume, using friction work in some condition of curve radius and axle load calculated by CONTACT and equation (4),and some experiment research work will be replaced too.
The result of experiment and numerical calculation is indicated that rail wear volume is severe in heavy axle load and small curve radius conditions. when other factors such as rail materials, wheel speed is assured, using friction work in some condition of curve radius and axle load calculated by CONTACT and empirical equation,and some experiment research work will be replaced.
Acknowledgments The research is financed by the National High Technology Research and Development Program of China (863 Program) (No. 2009AA04Z424), The National Natural Science Foundation of China(No. 50675183), The State 863 projects of china(2009AA04Z424).
Journal of the China Railway Society.1992,14(2):64-70 [7] Bolton P J, Clayton P, McEwan I J.

., Kamensk-Uralsky, Russia aurfu-science@yandex.ru, bchik63@mail.ru, cbobyann@mail.ru Keywords: EDS, EBSD, microstructure, Schmidt factor, heat treatment, Аl-Мg-Mn-Sc-Zr, aluminum alloy Abstract.
Materials and experimental procedure The study was carried out in order to establish the physical mechanisms of the influence of the TP of the ingots on the mechanical properties of Al-Mg-Mn-Sc-Zr aluminum alloy semiproducts.
Thus, for the metal of an ingot without TP the texture of the material is stronger.
Gołombek, The structure and mechanical properties of Al-Mg-Mn alloys shaped in the process of thermomechanical treatment, Journal of Achievements in Materials and Manufacturing Engineering. 45(2) (2011) 148-156

Lapel shaper Parametric Design for Automatic Liquid Packaging Machine Base on Visual Lisp Yadong Fang1,a, Wenke Xue2, Bo Sun1,b 1The Institute of Mechanical and Electrical Engineer Xi'an Technological University, Xi’an, China 2Wide-thick Plate Materials Company Baoti Group Ltd, BaoJi, China atomfangok@126.com, bwinkxue@163.com, csunbomm@163.com Keywords: Parameter design, lapel shaper, Visual Lisp Abstract.
Introduction Automatic liquid packaging machine is applicable to automatic filling and packing of liquid and paste material, such as milk, disinfection beverage and sauce.
Planar surface package material is shaped as cylindrical pouch through lapel shaper.
The theory and method discussed in the paper provides reference for lapel shaper rapid computer aided design among package machine design and manufacturing enterprises Acknowledgment It is a project supported by ShaanXi Province Education Department Natural Science Project (09JK479).
World Journal of Modelling and Simulation, Vol. 2, No. 2, pp. 129-133(in Chinese)