Search results

H., State-switched absorber for semi-active structural control, Journal of intelligent material systems and structures 11, 300-310, 2001
W., Vibration Control with State-Switched Piezoelectric Materials, J.
SPIE: Smart Structures and Materials, Damping and Isolation (Newport Beach, CA) 3989, 288-299, 2000
W., Vibration Control with State-Switched Piezoelectric Materials, J.
SPIE: Smart Structures and Materials, Damping and Isolation (Bellingham, WA) 5760, 402-412, 2005

Therefore, can choose the material is hard and good conductive properties of materials ( such as hard alloy ).
Influence of electrode wire and cutting fluid on the machining stability Influence of electrode wire on the machining stability The electrode wire: wire electrode material in high-speed WEDM is fast reciprocating operation, wire electrode is used repeatedly in the process, the electrode wire of different materials, impact on process indicators have different cutting speed.
The electrode wire materials are commonly used molybdenum wire, tungsten and molybdenum tungsten, in high speed wire cutting in the most commonly used are the molybdenum wire, molybdenum wire wire.
Because the cutting fluid is recycled, after a period of use, the cutting liquid includes many corrosion materials.
Chinese Journal of mechanical engineering .2001. electric spark linear cutting machine based on the statistical analysis (3) : 89 ~92.

Introduction Positron Annihilation Lifetime Spectroscopy (PALS) is sensitive to vacancy-like defects in materials [1].
In both materials, Si was the dominant impurity (i.e., 90 ppm and 1500 ppm).
Materials Preparation and Experiments Materials Characteristics and Preparation.
The materials referred below as "doped" samples contained SiO2 (1497 ppm), MgO (723 ppm), CaO (686 ppm), Fe2O3 (415 ppm) and Na2O (404 ppm).
Gœuriot: Accepted for publication in Journal of the European Ceramic Society [8] J.

(Fig.1) Inherit regional characteristics of architecture by the application of local materials.
The same wall made of different materials will bring out different effects.
And the local materials have become an important aspect in regional architecture through a long time development.
Native building materials inevitably affect regional architecture: native building materials give the building its character, and building is the carrier of local regional cultures.
Architectural Journal, 2002（5）；4—7 [2]Pan Guxi.

However, in most cases the cause of rising moisture sorption is fencing materials and condensation of water vapor in the interior of the enclosure.
Wet materials are less frost resistance and service life in terms of their alternate freezing and thawing is sharply reduced.
Increase of energy efficiency for educational institution building. (2014) Advanced Materials Research, Vols. 953-954, pp. 854-870
Increase of energy efficiency of the building of kindergarten. (2014) Advanced Materials Research, Vols. 953-954, pp. 1537-1544
Comprehensive method of energy efficiency of residential house (2014) Advanced Materials Research, Vol. 953-954. pp. 1570-1577

The Cring specimens cut from the tubing materials were fabricated according to ASTM G38-73 [9] (Fig. 1).
Symp. on Environmental Degradation of Materials in Nuclear Power System-Water Reactors, Inc.
Symp. on Environmental Degradation of Materials in Nuclear Power System-Water Reactors, TMS, Warrendale, PA (1987), p. 517
Symp. on Environmental Degradation of Materials in Nuclear Power System-Water Reactors, Inc.
Symp. on Environmental Degradation of Materials in Nuclear Power System-Water Reactors, TMS, Warrenendale, PA (1999), p. 689

When the sheet surface is irradiated with a laser beam, a fraction of the laser energy is absorbed in the material.
This steep temperature gradients result in the differential thermal expansion of the material which produces thermal stresses in the material leading to counter-bending of the sheet away from the laser beam.
Finite Elements Simulation Model The nonlinear heat transfer equation for isotropic materials can be written as (1) where T is the temperature, which is a function of coordinate and time; ρ is the density of the material; c is the specific heat, λ is the thermal conductivity; and Q is the source of heat being expressed as heat generation per unit volume in unit time interval.
J. of Manufacturing Science and Engineering 123 (2002) 73-81
Pantelkis, Numerical and Experimental Investigation of the Laser forming process, Journal of Materials Processing Technology 87 (1999) 281-290

Study on Preparation of PA6 / PDMS Blended Fibers and Fabric Properties Dong Suna and Guang Li* State Key Laboratory for Modification of Chemical Fibers and Polymer Materials, College of Materials, Science and Engineering, Donghua University, Shanghai 201620, China a1521259058@qq.com, *lig@dhu.edu.cn Keywords: Polyamide; polydimethylsiloxane; rheology; fabric properties Abstract: PA6 fibers and fabric properties were studied by adding PDMS, and PA6 / PDMS blend fibers were prepared by melt spinning.
Chinese Journal of Colloid & Polymer, 2008, 26 (2): 22-24
Rheological Study of Polyamide 6/Waste Styrene-Butadiene Rubber (SBR) Blends[C]// Materials Science Forum. 2012
Polymer Materials Science and Engineering, 2015, 31 (02): 103 -107.
Silicone Materials, 2014, 28 (06): 479-483.

The effect of water is related to large waste, reduction in quality, and shelf life of these materials.
One analysis of this figure reveals that all processes occurred in the falling drying rate, i.e., there is no constant drying rate period for both types of materials studied, in accordance to several works reported in the literature [28-29].
As stated earlier, there was no constant drying rate period for both types of materials, and the in natura cassava cube reached equilibrium moisture content in a shorter time than the osmotically dehydrated cassava cube.
Advanced Structured Materials,.
Official Journal of the Federative Republic of Brazil, Brasília p.5 Section 1 (2005).

Although the PM industry has existed for over a hundred years, the potential is indeterminate because the principle and the manufacturing processes allow for revolutionary materials and innovative technologies.
Further studies are necessary to determine LDV spectrum eigenvalue on different sizes, shapes, structures, and even product materials.
Powder metallurgy: science, technology and applications.
Journal of Manual & Manipulative Therapy, 17(2), 27E-38E
IOP Conference Series: Materials Science and Engineering,