Search results

Jung 1,b, K.H.
Kim 1,c, S.C.
Lim 1,d and H.S.
Reference [1] H.C.
Kim, Materials Science Forum, Vol. 475-479, (2005)pp. 967-970 [3] K.

Fig.1 showed the microstructure of Mo-Cr alloyed layer.
The dimension of surface carbides is less 1µm.
The dimension of surface carbide is less 1µm
References [1] Z.Q.
LIU, et al.: Materials Science Forum Vol. 475-479 (2005), pp. 3939-3942

The simulation results are compared with experimental results. 1.
The parameters of basic numerical calculation are shown in table 1.
The velocity field of different crank angle is shown in Fig.1.
References [1] Boese, H.L. and Hencey, Jr., T.R.
Phys, 1996, 64(4): 479-481

Li 1,2 , Z.J.
Zhao 1, T.B.
Oh 1, H.L.
Table 1.
Forum 437-438, 479 (2003) [4] X.P.

The photoluminescence (PL) measurement was performed at room temperature using a spectrofluorophotometer (SPEX, 1403); a He-Cd laser with the wavelength of 325 nm was utilized as a source of the PL measurements. 0 20 40 60 80 100 200 300 400 500 600 474 475 476 477 478 479 480 481 482 483 484 Applied Voltage (-V) Raman Shift (cm-1) 5nm 2nm Results and Discussion Nanostructural features.
A broad peak (~ 480 cm-1) and a shoulder peak (490 ~ 515 cm-1) indicate the presence of amorphous (a-Si) and nanocrystalline Si (nc-Si), respectively.
It was found that the shoulder peak shifted from ~ 500 to ~ 515 cm-1 in Fig. 1(b) and (c) as the DC bias varied from 0 to -600 V.
Units) Raman shift (cm -1 ) 1 2 3 300 350 400 450 500 550 nc-Si TO LO LA Intensity (Arb.
References [1] H.

At condenser temperature 230~420°C, the JIS standard value of grade 1 was satisfied.
280℃, as it was shown in Table 1.
The corrosion rates of the castings are shown in Figure 1.
References [1] S.
Forum Vol. 475-479 (2005), p. 513 0 20 40 60 80 100 120 140 160 180 U.T.S.・0.2%P.S.

Introduction Because of its light weight, high working pressure, safe and reliable connecting method, flareless tube fittings have a wide range of applications in aeronautical industry[1,2].
The axial symmetric solid element is chosen, and the model is shown in Fig.1 and Fig.2.
During the early of the tensile process, such an effect will limit the material in the area 1 flow, deformation occurs mainly in the area 2 of the tube material.
References [1] G.J.Li and M.
Zhan: Journal of plasticity engineering, Vol.15（2008）, p.54（in Chinese） [2] Information on http://www.tpub.com/content/aviation/ [3] G.J.Li, R.X.Zhang and W.Wu: Forging and stamping technology, Vol.35（2010）, p.79（in Chinese） [4]Y.S.Zeng: Materials Science Forum, Vol.475-479（2005）, p.3287

The structures and abbreviations of the final products were shown in Fig. 1, which were confirmed by 1H NMR and elemental analysis.
Fig. 1.
When the film was transferred from Cu(Ac)2 subphase, the corresponding peaks shifted to 1605, 1387 and 1306 cm-1, respectively.
References [1] A.
Liu: Thin Solid Films Vol. 479 (2005), p. 269

The design particle size distribution curve of rockfill is shown in Fig.1.
The test particle size distribution is shown in Fig.1.
References [1] T Hirose, et al.
Geotechnique, 1993, 43 (1), 53-67
Geotechnical SymPosium in Roma, March 16 & 17, 2006, 479-490

This platform consists of a dynamometer, and coaxially connecting motor with the parameters shown in Table. 1.
Figure.3 The experimental results with disturbance References [1] Q.B.
Zou: MICROMOTORS, Vol. 44 (2011), No.1, pp.31-34
Wang, J.Chen, and M.C.Li: TRANSACTIONS OF CHINA ELECTROTECHNICAL SOCIETY, Vol. 17 (2002), No. 1, pp.1-6
Serni: IEEE International Conference on Control Applications, (October 1-3, 2007), pp.479-484