Search results

Admixtures Cement concrete is the largest man-made contemporary engineering materials.
Application of Coal gangue In recent years, development of building materials of coal gangue is quite rapid.
(In Chinese) [3] H.B.FU: submitted to Construction Equipment and Construction Materials (2010).
(In Chinese) [12]B.JIA, R.H.ZHANG: submitted to Fujian Building Materials (2010).
Bui: submitted to Construction and Building Materials (2011) [15]P.K.Mehta: submitted to Advances in Concrete Technology.

Aligning Liquid Crystal Materials through Nanoparticles: A Review of Recent Progress.
Aligning Liquid Crystal Materials through Nanoparticles: A Review of Recent Progress.
Advanced Materials 2022, 34
Zeitschrift fur Naturforschung - Section A Journal of Physical Sciences 2004, 59
Journal of Polymer Science and Engineering 2023, 6, doi:10.24294/jpse.v6i1.2360

Anchor production process was also considered to improve gradient strength of materials which can better adapt to the rock burst environment.
Researches by Scholars [4~6] under the dynamic conditions of the support design were focused more on supporting materials and supporting methods than on support optimization.
Bolt material is optimized to improve the gradient strength.
Journal of CUMT International Journal of Mining Science and Technology, 2004,31(5):524-527
Journal of Shandong University of Science and Technology (Natural Science).2005,3.

LZSA was widely studied to produce materials by tape casting [4], injection molding [5], extrusion and by replication and direct foaming [6].
Abdullah, Journal of Environmental Management Vol. 90 (2009), p. 2287
Harris: Progress in Energy and Combustion Science Vol. 34 (2008), p. 667
Greil: Journal of Materials Processing Technology Vol. 206 (2008), p. 194
Tan: Materials Science and Engineering A Vol. 323 (2002), p. 232

And the nano Fe3O4/LDPE composite materials with different mass percentage concentration of 0.25 to 1 percent were prepared by melt blending.
Introduction Compared to common polymers at the macro level, Inorganic nano composite polymer materials shows unexpected characteristics such as light, electricity，magnetism and thermal aspects and demonstrates broad application prospect.It has become a concerning research direction in material science [1, 2].At present, many scholars mainly make the cross-linked polyethylene and low-density polyethylene as the basic materials and make various preliminary dielectric property study based on several concentrations of different inorganic nano-composite materials.
[2] Wenjun Zou, Jin Peng, Yun Yang: Materials LettersVol.61(2007), p. 725-729
[6] Xia Cheng, Shaoqing Chen, Xia Wang: Insulating Materials Vol.41(2008):44-48,in Chinese
[10] Liqiu Chu, Yu Chen, Wenjuan Su: Polymer Materials Science and EngineeringVol.27(2011), p.39-42,in Chinese

This paper reports on the bond strength comparison between silicon and different glass based materials via anodic bonding.
Figure 1: Bond Strength Test The bonded sample has two pieces of materials; one is a larger (3 cm Í 3 cm) and the other smaller (1 cm Í 1 cm).
Micro electromechanical systems (MEMS) based microfluidic devices for biomedical applications.International journal of molecular sciences, 12(6), 3648-3704
ECS Journal of Solid State Science and Technology, 2(9), Q165-Q171
Journal of Electronic Materials, 43(2), 555-566.

This method has been proven to be an effective approach for drilling, cutting and milling of various materials [6-9].
Materials and Methods A commercially-pure titanium (cp-Ti) rod having an average diameter of 2.070 mm was used as a workpiece in this study, and its chemical compositions are listed in Table 1.
Bhattacharyya, Pulsed Nd:YAG Laser Micro-turning of Alumina to Study the Effect of Overlap Factors on Surface Roughness Performance, IOP Conference Series: Materials Science and Engineering. 377 (2018) 1-7
Mathew, A comparison of dry and underwater laser micromachining of silicon substrates, Key Engineering Materials. 443 (2010) 693-698
Charee, V.Tangwarodomnukun, Underwater Laser Micromilling of Commercially-Pure Titanium Using Different Scan Overlaps, IOP Conference Series: Materials Science and Engineering. 303 (2018) 1-6

Materials and Results of the Research Technological scheme of the fist welding type.
Yudenkov, Time relaxation of point defects in p- and n-(HgCd)Te after ion milling, Journal of Electronic Materials. 32(7) (2003) 698-702
Balalayeva, Effect of particular combinations of quenching, tempering and carburization on abrasive wear of low-carbon manganese steels with metastable austenite, Materials Science Forum. 945 (2019) 574-578
Markov, Profitability of production of stainless steel + zirconium metals combination adapters, Key Engineering Materials. 864 (2020) 285-291
Gurenko, Modeling dynamic parameters of hard alloys during shock wave regeneration, IOP Conference Series: Materials Science and Engineering. 969(1) (2020) 012079

Active Vibration Control of Piezoelectric Material Using Fuzzy Logic Controller Tao Hu1,2,a, Qibai Huang1,2,b,Shande Li1,2,c 1School of Mechanical Science & Engineering, Huazhong University of Science & Technology, Wuhan, 430074, PR China 2Hubei Institute of Specialty Vehicle, Suizhou, 441300, PR China aemail: alvin.hutao@foxmail.com, bemail: qbhuang@mail.hust.edu.cn, cemail: lishande@foxmail.com, Keywords: active vibration control, fuzzy logic controller, PID control, piezoelectric actuator/sensor Abstract.
Piezoelectric actuators are being increasingly studied and used in different areas of science and technology due to their nanometer displacement resolution, wide bandwidth, fast response and high stiffness [2].
Consequently, the feasibility of adopting piezoelectric materials as actuators and sensors for controlling vibrations in flexible structures has received increasing attention.
Piezoelectric materials provide inexpensive, reliable, and non-intrusive means of actuating and sensing vibrations in flexible structures.
[2] Morteza Mohammadzaheri, Steven Grainger, Mohsen Bazghaleh, Fuzzy Modeling of a piezoelectric actuator, International Journal of Precision Engineering and Manufacturing, May 2012, Volume 13, Issue 5, pp 663-670 [3] D.

Synthesizing Effect Model Based on Quasi-linear Function in Intelligent Materials System Shuxin Luo a, Jing Li b, Fachao Li c College of Science, Hebei University of Science and Technology, 050018, Shijiazhuang China ahappy_luo@126.com, blijing19820619@163.com, clifachao@tsinghua.org.cn Key words: interval numbers; compound quantification strategy; synthesizing effect function; quasi-linear function; order structure Abstract.
European Journal of Operational Research 188, 1-13 (2008) [3] Xingfang Zhang, Xingwei Zhang: The Ranking of Interval Number and Its Application to Decision of Systems.
Journal of Tangshan Teachers College, Vol. 9, 45-47 (2004) [7] Wenyi Zeng: Comprehensive Decision Model of Interval Number.
Journal of Engineering Mathematics, Vol. 18, No. 4, 103-109 (2001) [9] Zeshui Xu, Qingli Da: Research on Method for Ranking Interval Numbers.
Operations Research and Management Science, Vol. 12, No. 3, 13-17 (2003).