Search results

Therefore, studying loess foundation treatment technology is significant science meaning and application value for earthquake damage-defense construction project of liquefied loess area, reducing casualties and property loss caused by the earthquake.
However, the loess liquefaction engineering assessment method and liquefaction potential loess foundation processing technology research material is few, the technology and methods is not mature.
Depend on numerous materials, the preliminary research indicates that the Q21and Q1 loess do not have liquefaction potential.
Acknowledgements This paper was financially supported by the National Natural Science Foundation of China (50978239), and the Basic Scientific Research Business from Institute of Earthquake Science, CEA (2012IESLZ07,2012IESLZ01).
Chinese Journal of Geotechnical Engineering, Vol.1(2000) p. 89 “In Chinese”

The study of radiation influence on reactor materials requires quantitative characteristics allowing comparison of material irradiation results in different nuclear reactors.
Many groups of researchers all over the world performed numerous simulations of a variety of materials.
Bloom et al., Materials to Deliver the Promise of Fusion Power—Progress and Challenges, J.
Baluc, Materials for Fusion Power Reactors, Plasma Phys.
Smither, SPECTER: Neutron Damage Calculations for Materials Irradiations, ANL/FPP-TM-197 (1985)

Numerical Simulation Modeling of GPR on Road Disease ZHAI Bo1, a, GONG Zhimin2,b 1Institute of automation, Chinese academy of sciences, China 2China nuclear power design company LTD, China azhaibo7227@126.com, bgongzm2004@126.com Keywords: GPR, FDTD, numerical simulation, road disease Abstract.
According to the material and road grade, the thickness of the layers can be changed.
The existing road surface is generally two kinds of materials: modified asphalt concrete or cement concrete.
Journal of chongqing jiaotong university.

Introduction With the advancing constantly of science and technology in China, underground engineering is beginning to receive more attention, especially for subway tunnels in city.
(1) (2) Where, is density of material along vertical model boundary; Cp and Cs are p-wave and s-wave speed at the side boundary; A is area of influence of free-field grid point, Vxm and Vzff are x-velocity and z-velocity of node in main grid at side boundary, Vxff and Vzff are x-velocity and z-velocity of node in side free field, Fff is free-field grid point force with contributions.
Acknowledgements This work was financially supported by Beijing Higher Institution Engineering Research Center of Structural Engineering and New Materials, BUCEA.
LIU: China Civil Engineering Journal, vol. 4 (2008) No.41, p.73.

Table1 Sample specification Fabric structure Material Fineness Grams per square meters(g/㎡） Surface layer Inner layer Polyester filamen cleancool /cotton blended 1 polyester cover cleancool fiber structure polyester filamen cleancool /cotton blended 150D 14.6tex 257 2 Honeycomb-like Mesh cleancool /cotton blended 14.6tex 224 3 Honeycomb-like Mesh polyester/cotton blended 14.6tex 203 4 Honeycomb-like Mesh cotton fiber 14.6tex 221 The test of the indexes The Selection of the Property Indexes.
This result means that materials of the fabrics also has important influence on its comprehensive performance.
Xuebin Me, Fugang Wang; Jianfeng Cao.The application of Fuzzy Comprehensive Evaluation on Water Quality and Discussion, Word Geology 2000（2） [3] ShuxuanLiagn; Hong Wu; LI Zhanchen Li; Fuzzy mathematics-based comprehensive evaluation of dynamics of atmospheric environmental quality, Journal of Arid Land Resources and nvironment,2010（6） [4] Yanjun Liu, Jun Xu, Wenjun Zhu.
Research on Finishing of Yak Fine Hair Kitted Fabric Style Made to Imitated Cashmere Kitted Fabric Style, Shanghai Textile Science & Technology, 2003（2）

Materials and Methods The chemical composition of the Al 2024-T3 alloy used in this study, provided by Alcoa, is shown in Table 1.
Trillo: Journal of Material Science Vol. 35 (2000), p. 3479

Then the conductivity of the thermal insulation material and the heat transfer coefficient of the energy-saving wall can be measured accurately and reliably with a significant reduction of human error.
Acknowledgement The research work was financially supported by the Research and development project of Ministry of Housing and Urban-Rural Development under Grant No. 2010-k1-19, two Research programs of Zhejiang Province under Grant No. 2010C31084 and No. 2009C31042, and Science and technology project of Jiaxing under Grant No. 2009AY2034.
Cheng: New Building Materials Vol. 10 (2009), p. 42-44
Yan, et al: Journal of Ningbo University Vol.12 (2008), p.581-583

Effect of anode size, membrane and membrane size on power generation and wastewater treatment in Microbial Fuel Cells Guangyu Zhou a, Yuichiro Yoshino b, Takahiro Yamashita c, Takahiro Sato d and Yasunori Kawagoshi e Graduate school of science and technology, Kumamoto university, 2-39-1, Kurokami, Kumamoto, 860-8555, Japan asyuukouu@gmail.com, byuichiro.0708@softbank.ne.jp, cyamazi.3219@i.softbank.jp, dsato@tech.eng.kumamoto-u.ac.jp, egoshi@kumamoto-u.ac.jp Keywords: MFCs, biomass energy, abiotic factor, wastewater treatment, orthogonal experiment Abstract.
Compare with biotic factors, abiotic factors as reactor conduction, material of electrode, temperature, PH and so on are easy to control.
Materials and Methods Reactor configuration.
Tuovinenb, Cathodic limitations in microbial fuel cells: An overview, Journal of Power Sources. 180 (2008) 683-694.

Although TiN films have numerous advantages, their adhesion strength are inadequate when they are deposited on soft substrate such as pure titanium, plastic deformation is prone to occur with high loads which will lead to the film decohesion because soft material may not be able to provide adequate support for the hard TiN film.
Progress in Materials Science, Vol. 54(2009), p.397-425 [2] Shinji Takemoto, Masayuki Hattori, Masao Yoshinari, Eiji Kawada, Yutaka Oda: Corrosion behavior and surface characterization of titanium in solution containing fluoride and albumin.
The Journal of Prosthetic Dentistry, Vol. 96(2006), p.12 [5] H.

The file can be input into RP machine to manufacture prototype of product for various purposes with different methods and different RP materials [3].
Finally, the 3D solid model is loaded in Ansys for building FEM model according to material properties and boundary conditions, as shown in Fig. 4d1), 4d2).
(Beijing: Mechanical Industrial Press,P.R.China, 2005) [4] Ren Guocheng, Wan Guangchun: Journal of Shandong University(Engineering Science) Vol. 03 (2004, p.5) [5] Yang Lilin: Modular Machine Tool & Automatic Manufacturing Technique.