Search results

Materials and Methods Selection of Sensors.
The pH variation is not commonly considered for sensor compensation because it's universally believed that the material composition of the modern sensors is well resisted to any chemical erosion.
Journal of Hydrology (2007) 344, 32–42
Importance of spatial structures in advancing hydrological sciences [J].

The prerequisite of configuration design is to build the perfect GBOM (General Bill of Material).
References [1] Weibing Xin,Yibing Liu and Ying He: submitted to Automation&information of Power Station(2009) [2] Ning Bai,Lin Yang,Tieqiang Ma: submitted to Modular Machine Tool&Automatic Manufacturing Technique (2011) [3] Donghai Su, Meiyan Zhang, Tieqiang Ma: submitted to Advanced Materials Research(2010) [4] GAURY E G A, KLELINEN J P C, PIERREVAL H: submitted to Journal of the Operational Research Society (2001) [5] Zhengxing Sun, Fuyan Zhang,Shijie Cai: submitted to Department of Computer Science and Technology (1998) [6] Tiebo Sun: submitted to Mechanical Engineering&Automation (2009)

Another is that the salinity in the soil mainly originates from the materials constituting the soil.
Hence for many researchers, the environment-friendly or the waste material arising from the production is prioritized for the soil conditioner, such as weathered coal, fermentation residues, mineralized waste and green waste, etc [4].
Journal of Daqing Petroleum Institute, 2004, 28(4):15-17 [2] Xiaojie Chen, Ningyuan Ma.
Anhui Agricultural Science, 2008, 36(20):8751-8716

Moreover, linearity and non-linearity can refer to both the geometry of the model and its material model is considered linear if under the influence of loads it has small deformations, and the relationship between deformations and stresses is linear, i.e. it obeys Hooke's law.
The model was tested for adequacy using the well-known formulas of the material resistance based on the calculation of the beam for strength and rigidity in oblique bending [13].
The model was tested for adequacy using the well-known formulas of the material resistance based on the calculation of the beam for strength and rigidity in oblique bending [13].
Chigirinsky, Mathematical model of formation the axial component of the cutting forces at turning structural alloyed steel 3120 [Electronic resource], Modern scientific research and their practical application: research bulletin SWorld: [electron. journal], No. 6, vol.
J11410 (Technical Sciences), (2014) 232-238

The workpiece material used for the experiments is aluminum alloy of class 7075 T651 (AlZn5.5MgCu).
This material has very high strength and therefore is used widely in applications in aerospace and in military industry.
This is expected since by increasing the volume of removed material the main cutting force increases too leading to cutting tool deflection, which yields higher roughness.
Smith, Machining Dynamics Frequency Response to Improved Productivity Springer Science + Business Media, LLC 2009 [2] Altintas Y. – Budak E., Analytical Prediction of stability lobes in milling, 1995 [3] Altintas Y., Manufacturing Automation – Metal cutting mechanics, machine tool vibrations and CNC design, second edition, University of British Columbia, Cambridge University Press, 2012 [4] L.N.
Fernández de Bustos, Recording of real cutting forces along the milling of complex parts, Mechatronics 16 (2006) [5] Karachaliou Ch. – Mansour G., Dimensional metrology, Ziti publications (2007) [6] Antoniadis A., Savakis C., Bilalis N. and Balouktsis A., Prediction of Surface Topomorphy and Roughness in Ball-End Milling, The International Journal of Advanced Manufacturing Technology (2003)

The shape of electrostatic spray device is shown in Fig.2, the housing of the spray gun is machined from nylon material, the electrode ring is made of copper tube instead of copper rod, whose inner diameter is 0.085m and outer diameter is 0.095m.
Fig.3 Schematic of experiment system Fig.4 Physical map of experiment system In Fig.3, (1)air compressors(2)(5)(10)(11)(15) pressure gauge(3)cut-off valve(4)expansion tank (6)pressure tank(7)control cabinet(8)gun switch(9)pressure regulating valve(12)atomizing air regulating valve(13)high-voltage electrostatic generator(14)spare part(16)hydraulic regulating valve(17)rotameter(18)stepper motor(19)conveyor belt (20)fabric(21)electrostatic spray device Experimental materials and methods.
Acknowledgements This work was financially supported by National Nature Science Foundation of China (51006047).
Studies on the Charging Effect of Ultra-Low Volume Electrostatic Charging Spray Machine [J], Journal of Yunnan Agricultural University. (1995), 10(3): 202-206.

Experimental Material.
Journal of China University of Petroleum (2007).
(In Chinese) [5] Wanli Kang, Lingwei Meng, Jinggang Niu, et al. polymer materials science & engineering (2006).

Therefore, the module has management features, shape features, structural features, precision features, technical characteristics, material characteristics, functional characteristics and assembly characteristics of the property, etc.
Module family model shows the composition of module family, that is, the BOM (Bill Of Material) of module family.
Since each product has many features, including qualitative and quantitative characteristics of features, such as shape characteristics, structure characteristics, accuracy level features, technology characteristics, material characteristics, function characteristics and assembly characteristics.
This paper gave the evaluation index of the program evaluation of module combination, established the hierarchical structure model, and presented the process of algorithms based on AHP to configure the program evaluation of module combination. 1 This work is supported by Fundamental Research Funds for the Central Universities (N090403005) and Research Funds for Science Technology Projects of Liaoning Province (2009402017, 2010220003).
Journal of Dalian University of Technology, 2006, 46(4): 510-515 [4] Gao Guangda, Xu Yanshen, Lin Hanbao, Chai Baolian, Wang Wei.

Journal Citation (to be inserted by the publisher) Copyright by Trans Tech Publications Co-sputtered carbon-nickel nanocomposite thin films A.
On the other hand, carbon based materials such as diamond-like carbon and amorphous carbon nitride alloys have been extensively applied as protective coatings in magnetic storage devices, due to their excellent mechanical and tribological characteristics [7].
While this material is not particularly hard, its mechanical properties can be easily optimized by the incorporation of nitrogen [8].
Rolison: Science Vol. 284 (1999), p. 622

Introduction Nowadays, there is an increase in the number of ecologically aware studies and their practical applications, such as the development and use of alternative environment-friendly materials.
Thereafter, the material was slightly pressed at 150oC for 1h.
, Composites Science and Technology, 63 (2003), 1259-1264
[2] Gomes, A., Goda, K. and Ohgi, J., "Effects of Alkali Treatment to Reinforcement on Tensile Properties of Curaua Fiber Green Composites", JSME International Journal, 47(2004), 541-546.