Search results

Acknowledgements This work was financially supported by the National Natural Science Foundation of China (No.51304159 and No.51374170) References [1]Chen XiQing,Research on the control system of oil extraction joint station based on PLC[D],Daqing Petroleum Institute,2008.6
Powers, Simulations of pulsating one-dimensional detonations with true fifth order accuracy, Journal of Computational Physics,Volume 213, Issue 1, 20 March 2006, Pages 311-329）
Dynamic material behavior under bi-axial loading [A], Proceedings ofInternational Conference on Fundamental Issues and Applications of Shockwave and HighStain Rate Phenomena (EXPLOMET2000)[C].

Introduction At present, siliocon carbide (SiC) is known as a leading wide bandgap semiconductor material because of its high tolerance to harsh environments, such as high temperature and radiation [1].
McLean: Total ionizing dose effects in MOS oxides and devices, IEEE Transactions on Nuclear Science, vol. 50, no. 3, pp. 483-499 (2003) [12] M.
Kimoto: Normally-off 400 ◦C Operation of n- and p-JFETs With a Side-Gate Structure Fabricated by Ion Implantation Into a High-Purity Semi-Insulating SiC Substrate, IEEE Electron Device Letters, vol. 40, no. 6 (2019) [13] Pak, Amin and Orouji, Ali A.: A novel high performance LDMOS transistor with high channel density, Journal of Computational Electronics, vol. 17, pp 217-223 (2018) [14] M.

For the derivation of the inelastic displacement, the following assumptions are used: (a) the chords are only axially loaded; (b) dynamic influence of the structure is neglected; (c) the material follows Hook's law; (d) The friction between components can be ignored.
Acknowledgment This Research is partly supported by the National Natural Science Foundation of China (Grant No.51178458) which is gratefully acknowledged by the all authors.
Journal of shijiazhuangrealwaynstituten, 2000, 13(45).

Because each factors such as the raw material, structure of yarns, structure of fabric, density of warp and weft yarns, after treatment etc. was related to the moisture sorption, air permeability and capillary effect properties of fabric, the only changed factor were blended ratio and density of weft yarns in the bamboo pulp/cotton fabric, and all the structure of fabric were used cassimere twill and density of warp yarn was 445 root/10cm.
References [1]HE Fang，ZHOU Jing-yi.Research of wet comfort plain fabric[J].Journal of Tianjin Polytechnic University，2011，30（1）：32-35 [2]JIANG Li-yun, WU Wei-min, SUN Qing.
Shanghai Textile Science & Technology，2006，34（12）：62-63

Comprehensive risk analysis of Dongting lake dike engineering Dehua Mao1,a, Zhilong Li1,b, Xinguang He1, Zhengzui Li2, Dongrun Liu2, Kabo Liu 3,c 1 College of resources and environment science, Hunan normal university, Changsha, 410081, China 2 Hunan Provincial Hydrological Bureau, Changsha, 410007, China 3 Management Department of Dongting Lake Engineering, Hunan Province, Changsha, 410007, China amdh408122@sohu.com, bzsulizhilong@yahoo.com.cn, cliukabo_2007@126.com Keywords:comprehensive risk analysis; dike engineering; Dongting Lake Abstract: Comprehensive risk analysis mode including overtopping risk, slide instability risk and seepage risk has been established.
Overtopping risk analysis adopted the highest water level material from 1953 to 1996 in Yangdi hydrological station near this section of the dike.
Li, Risk analysis and computation of flood control capacity for river dike , Journal of Changjiang academy, 2(2001)7-10

Introduction Along with the development of the level of electric power equipment manufacturing technology, in our country, improving the parameters of the equipment can make equipment material enhances the sensitivity on the operating condition of aqueous vapor, correspondingly, the requirements for the processing accuracy of the chemical water treatment, security and reliability are more strict.
Journal of Northeast China Institute of Electric Power Engineering,2003,23(4):38-43 [5] Wang Yinggao, Li Baoguo,Zhang Jianli.
Inner Mongolia Science Technology and Economy,2004,20:41-43.

Four specimens were strengthened with 10-mm diameter deformed CFRP rods which were manufactured by Harbin Tider Science & Technology Inc, Chinese.
It had been proved by the material test that the ultimate tensile strength was 2100 MPa and the Young’s modulus was 150 Gpa.
CFRP-strengthened and corroded RC beams under monotonic and fatigue loads [J].Journal of Composites for Construction,2001,5(4):228-236 [2] Zhang Ke，Ye Lieping，Yue Qingrui.Experimental study on flexural fatigue behavior of RC beams strengthened with pretressed CFRP sheets [J].

Simulation-Driven Insights into Heat Transfer During Copper Mold Casting of Magnesium-Based Bulk Metallic Glasses Rajesh Kumari Rajendran1,a, Abhilash Viswanath2,b and Rajashekhara Shabadi1,c* 1UMET, Unité Matériaux et Transformations CNRS UMR 8207 - Université de Lille, France 2CSIR- National Institute for Interdisciplinary Science and Technology, Trivandrum, India arajesh.kumarirajendran@univ-lille.fr, bviswan.abhilash@gmail.com, c*Rajashekhara.shabadi@univ-lille.fr Keywords: Copper mold casting, Numerical simulation, Magnesium bulk metallic glass Abstract.
Thermo-physical properties of the magnesium-based ternary alloy and the copper mold are sourced from the FLOW-3D™ material database as listed in Table.1 Table 1.
Pillai, Numerical simulation and experimental validation of free surface flows during low pressure casting process, Journal of MaterialsProcessingTechnology,Volume244,2017,Pages320-330,doi: 10.1016/j.jmatprotec.2017.02.003 [8] J.

Acknowledgements This work was financially supported by the Nation Natural Science Foundation of China (NSFC) (Program No.51279109).
Environment effect of Geotechnical material[M].
China Civil Engineering Journal, 2002,35(4): 82-85.

To ensure that the weld has a certain strength after welding, the wire which has the intensity level of ER76-G is chosen, whose parent material is Q690.As shown in table 1, the parameter values of the average displacement of the deformation δ which 40 sets of different welding current I, welding voltage U, welding speed v and flow of gas qm are corresponding to are collected.
Measurement Science and Technology, 2007, 18(7): 1818-1822
Journal of Central South University, 2014, 21(3):1085-1090.