Search results

Chemical composition of the material Cr33Ni50W5Mo3TiAlB.
Acknowledgments The study was carried out at the expense of a grant from the Russian Science Foundation № 24-19-00765, https://rscf.ru/project/24-19-00765/.
[2] Gabriele Piscopo, Luca Iuliano, Current research and industrial application of laser powder directed energy deposition, The International Journal of Advanced Manufacturing Technology, 119 (2022) 6893-6917
Razzhivin, Practical approbation of thermodynamic criteria for the consolidation of bimetallic and functionally gradient materials, Metals, 11(12) (2021) 1960
Makwana, Parametric optimization to improve the machining process by using Taguchi method: a review, Materials Today: Proceedings, 47 (2021) 2709-2714

If the spheres are of identical material, then γ12 = 0.
It is an equilibrium theory, it is only valid for short range surface forces and compliant materials (Tabor parameter greater than unity [7]), and provides no guidance on attractive forces prior to contact.
The rubber material was dicumyl peroxide cured synthetic polyisoprene.
The JKR equation that emerged from the work has found use for the interpretation of adhesion results for a wide range of materials and nanotechnological setups.
Manufacturing Engineering Vol.23 (2007) p. 47-50 [40] D.B.Hough and R.H.Ottewill: Colloid and Interface Science IV Ed M.Kerker (Academic Press, New York, USA 1976)

Introduction Currently, the market demand for using natural products is increasing, in which extracts and compounds with natural materials for beauty are also paid more attention.
And the research works related to the development of personal care products from the source of coconut oil in the locality of Ben Tre province are still limited in the results published in prestigious domestic and national scientific journals.
Thus, with the potential of coconut oil sources available at Ben Tre, this research has been active in the source of raw materials to produce natural cosmetic products from coconut oil through the saponification of coconut oil.
Material and Methods Raw materials and chemicals.
Acknowledgements This study was supported by Ben Tre Department of Science and Technology, Ben Tre Province, Vietnam under the grant number 1136/HĐ-SKHCN.

The transfer process was done so that all the structure properties, such as geometry, materials, assigned loads, frame and shell sections, and joint constraints, remained the same.
The structural members, such as columns, beams, and conventional braces, are made of steel material of grade Q345, with a nominal yield strength, fyk, of 345 MPa.
The yield deformation was calculated based on elastic modulus of steel, Es, and the yield force, which was computed using the material nominal yield strength, fyk = 235 MPa.
Acknowledgements This research work was supported by the National Key Research and Development Program of China (Grant No. 2016YFC0701101) and the National Natural Science Foundation of China (Grant No. 51678449).
Sun, Application of buckling-restrained braces (BRB) in RC frame-bent main building structure for large thermal power plants, Journal of Industrial Construction 44(8), 98-102, 2014.

Photocatalytic Activity and Antibacterial Properties of ZnO/CNTs Composites Hongwu Zhu1,a, Yusong Pan2,b *, Yuanqing Wang3,c, Yanlei Xiang4,d, Rong Han5,e and Run Huang6,f* 1,2,3,4,5,6Department of Materials Science and Engineering, Anhui University of Science and Technology, Huainan 232001, P.
Zinc oxide (ZnO) semiconductor has lots of advantages such as longer shelf life, low toxicity, low price, and good environmental acceptability, making its potential application materials for antibacterial applications and sewage treatment.
Experimental Details 2.1 Materials CNTs with diameter in the range of 8-15 nm and length less than 50 μm, were supplied by Xianfeng Nano Materials Technology Co., Ldt.
Table 1 Comparison of photocatalytic performance of various ZnO/CNTs composite materials Sample Dye name Sample dosage (mg) Dye amount (mL) Dye concentration (mg/L) Light source Time (min) Efficiency (%) Ref.
Onwudiwe, Adsorption and photocatalytic removal of Rhodamine B from wastewater using carbon-based materials, Flatchem 29 (2021) 100277

Dentin exhibits a behavior like a functionally graded material with properties dependent on tubule density and orientation.
However, Eq. (5), properly related to isotropic materials, is not the correct relationship to calculate dentin Poisson’s ratio.
FIMEC (Flat-top cylinder Indenter for MEchanical Characterization) is an instrumented indentation technique, developed by one of the authors to test metallic materials on a local scale.
The interpolating function consists of two exponential terms with relaxation times τ1 and τ2, which describe two different mechanical processes typical of porous materials.
Journal of Dentistry, Tehran University of Medical Sciences, Tehran, Iran.

These low mean rolling temperatures lead to higher stress in materials since the strength of the material is dependent on temperature.
Acknowledgments The Staff Members in the Department of Materials, Manufacturing and Industrial Engineering, Faculty of Mechanical Engineering and ISI, Universiti Teknologi Malaysia are sincerely appreciated for their financial and technical support during and after this work.
A (2009), “Rolling Temperature for Steel Hot Flat rolled at Low Strain Rates”, Advanced Materials Research, Vol. 62-64, pp. 317-323
[10] LENARD, J.G. (1980), “Roll Deformation in Cold Strip Rolling’’ Journal of Engineering Materials and Technology”, ASME Vol. 102, pp. 382 – 383
[12] SELLARS, C.M. (1981), “Les Traitments Thermomecaniques”, 24eme Colloque de Metallurgie, Institut National des Sciences et Technique Nucleaires, Sanclay, pp. 111 - 120

Norelyza3,c 1Department of Civil and Construction Engineering, Faculty of Engineering and Science, Curtin University Malaysia, Miri, Sarawak, Malaysia 2AMR Environmental Sdn.
Material and Methodology Sample.
Rashid, Performance of MR-deDuster: A case study of a palm oil mill plant, Advanced Materials Research. 664 (2013) 133–137
Prasad, Process modeling and particle flow simulation of sand separation in cyclone separator, Particulate Science and Technology: An International Journal. 33 (2015) 385-392

Table 1 Effect of different radiations on semiconducting materials S.No.
These materials are also used as ion-selective membranes for chemical sensors.
The glassy materials in the form of ingots were obtained by breaking the quartz tubes.
Thermal evaporation method has been used to prepare thin films of these materials.
Weighted materials are placed in the Tungsten or Molybdenum boat connected between the two copper electrodes.

To estimate the consumer attitude to the technical and economic features of the product and optimize the dialogue between the consumer and the producer of the science-intensive we suggest a method which involves the following stages.
Although z1 production (M-138/2 (YuMZ)) and z4 production (JOY (USA)) have similar aggregates of expert assessments but the high degree of compatibility of z1 production (M-138 /2 (YuMZ)) with the parameters “high quality of science-intensive products” and “high production efficiency” make it more preferable.
Measuring the fuzziness of sets. – Journal of Cybernetics, 1974. v. 4, p. 53-61
Applied Mechanics and Materials Volume 379, 2013, Pages 207-213
Competitiveness of science-intensive engineering production: economics and management: monograph. – Tomsk: Tomsk State University of Control Systems and Radioelectronics Press, 2002. – 247 p.