Paper Titles
Interface Reaction of CNTs/Al Composites Fabricated by High Energy Ball Milling
p.90
The Propagation of In-Plane Waves in Multilayered Elastic/Piezoelectric Composite Structures with Imperfect Interface
p.95
Hot Compression Performance of TiC10/Cu-Al2O3 Composite Prepared by Vacuum Hot-Pressed Sintering
p.99
Study on Pore Structure of Multi-Layered Spunbonded Nonwovens
p.103
Morphology, Dynamic Mechanical and Mechanical Properties of Long Glass Fiber Reinforced Polypropylene and Polyvinyl Chloride Composites
p.107
Preparation of 3D Honeycomb Basalt Fibers Woven Composites
p.111
SiCp/7050 Aluminum Matrix Composite Made by High-Energy Ultrasonic and Two Steps Casting Processing
p.115
Correlation between Curing Temperature and the Properties of Conductive Composites
p.119
Effect of Functionalized Multi-Walled Carbon Nanotubes on the Interfacial Properties of Ramie Fiber/Polylactic Acid (PLA) Composites
p.123

Morphology, Dynamic Mechanical and Mechanical Properties of Long Glass Fiber Reinforced Polypropylene and Polyvinyl Chloride Composites

Article Preview

Abstract:

The influence of long glass fiber (LGF) content on properties of PVC/PP composites were investigated by means of scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), and mechanical properties. The experimental results demonstrate that long glass fiber could effectively improve the mechanical properties and storage modulus of PVC/PP. The DMA reveals good miscibility between PVC and PP. Based on SEM, good interfacial adhesion between matrix and long glass fiber in PVC/PP/LGF composites was observed. All results in this paper were consistent, and showed long glass fiber could effective influence the properties of PVC/PP, which were proved by the mechanical properties of the composites.

You might also be interested in these eBooks
Advanced Engineering Materials III View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 750-752)

Pages:

107-110

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.750-752.107

Citation:

Cite this paper

Online since:

August 2013

Authors:

Bang Sheng You*, Kai Zhou Zhang, Jian Bing Guo, Li He

Keywords:

Composite, Long Glass Fiber, Mechanical Property, Morpholoy, Poly(vinyl chloride), Polypropylene (PP)

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2013 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

* - Corresponding Author

References

[1] Thomason JL. The influence of fiber length and concentration on the properties of glass fiber.

Google Scholar

[2] Thomason JL. The influence of fiber length, diameter and concentration on the impact.

Google Scholar

[3] H. BIJSTERBOSCH, R. J. GAYMANS. Polyamide 6-Long Glass Fiber Injection Moldings. POLYMER COMPOSITES, 1995, 16(5): 363-369 performance of long glass fibre reinforced polyamide: 6, 6. Composites Part A 2009; 40: 114–124. reinforced polypropylene.

DOI: 10.1002/pc.750160504

Google Scholar

[4] The properties of injection moulded long fiber PP at high fiber content. Composites Part A 2005; 36: 995–1003.

Google Scholar

[5] S. Hashemi. Temperature, strain rate and weldine effects on strength and micromechanical parameters of short glassfibre reinforced polybutylene terephthalate (PBT). Polymer Testing 30 (2011) 801–810.

DOI: 10.1016/j.polymertesting.2011.07.006

Google Scholar

[6] Hassan A, Yahya R, Yahaya AH, et al. Tensile, impact and fiber length properties of injection-molded short and long glass fiber-reinforced polyamide 6, 6 composites. J Reinf Plast Comp2004; 23: 969–986.

DOI: 10.1177/0731684404033960

Google Scholar

[7] Karger-Kocsis J and Friedrich K. Fracture behavior of injection-molded short and long glass fiber-polyamide 6. 6 composites. Compos Sci Technol 32(1988) 293–325.

DOI: 10.1016/0266-3538(88)90067-x

Google Scholar

[8] Srinivasan V, Karthikeyan R, Ganesan G, et al. Comparative study on the wear behavior of long and short glass fiber reinforced plastics. Met Mater Int, 2010, 16: 205–212.

DOI: 10.1007/s12540-010-0407-y

Google Scholar

[9] Karger-Kocsis J and Friedrich K. Fatigue crack propagation in short and long fibre-reinforced injection-moulded PA 6. 6 composites. Composites 19(1988)105–114.

DOI: 10.1016/0010-4361(88)90720-3

Google Scholar

[10] Menard, K. Dynamic Mechanical Analysis: A Practical Intro-duction; CRC Press: New York, (1998).

Google Scholar

[11] Nair, S.V.; Subramaniam, A.; Goettler, L.A., Fracture resistance of polyblends and polyblend matrix composites: Part III role of rubber type and location in nylon 6, 6/SAN composites, J. Mat. Sci, 33, 3455-3464(1998).

Google Scholar