Papers by Author: Rodrigo Martins

Abstract: Thin film transistors (TFTs) have been produced by rf magnetron sputtering at room temperature, using non conventional oxide materials like amorphous indium-zinc-oxide (IZO) semiconductor, for the channel as well as for the drain and source regions. The obtained TFTs operate in the enhancement mode with threshold voltages of 2.4 V, saturation mobility of 22.7 cm2/Vs, gate voltage swing of 0.44 V/dec and an ON/OFF current ratio of 7×107. The high performances presented by these TFTs associated to a high electron mobility, at least two orders of magnitude higher than that of conventional amorphous silicon TFTs and a low threshold voltage, opens new doors for applications in flexible, wearable, disposable portable electronics as well as battery-powered applications.

Abstract: In the present work, the spectroscopic ellipsometry (1.5 - 5.5 eV) was used to investigate the effects of current density induced microstructural variations and their influence on the electronic states of as-prepared and a-Si:H coated porous silicon (PS). The pseudodielectric responses of the low and high current densities (5 and 40 mA/cm2) were analyzed using a multilayer model within the effective medium approximation. The FTIR investigation reveals the enhancement of surface oxide (Si-Ox) layer with current density and the improvement of the Si-Hx band after a-Si:H coating.

Abstract: Total hip replacement is a common practice in every day clinical work. Artificial hip implants consist of a femoral component and an acetabular component. Nowadays the acetabular component is composed of a polymeric cup and a metallic shell. This study focuses the development of an innovative acetabular component substituting the metallic shell by a multilayer coating on the acetabular cup. A titanium coating was deposited onto ultra-high molecular weight polyethylene (UHMWPE) samples by physical vapour deposition (PVD), having an in situ pretreatment with argon ion bombardment in order to optimize the adhesive strength by surface modification, followed by the deposition of a thin film of hydroxyapatite (HA) using rf magnetron sputtering technique, at room temperature. Results obtained seem to indicate that these multilayer coatings can be a viable alternative to the metallic shell, leading to the substitution of a two part for a one part acetabular component.

Abstract: Electrochromic materials have attracted considerable attention during the last two decades as a consequence of their potential application in several different types of optical devices. Examples of these devices include intelligent windows and time labels. In this paper the authors describe results obtained with thin tungsten oxide films produced at room temperature by rf magnetron sputtering under an argon and oxygen atmosphere on transparent conductive oxide coated glass substrates. To protect the surface of the electrochromic film, prevent water absorption and obtain a good memory effect under open circuit voltages, a layer of Ta2O5 was deposited over the WO3 films. In this study, the effect of different electrolyte compositions on the open circuit memory of optical devices has been characterized. The best results were obtained for electrochromic devices with polymer gel p(TMC)3LiClO4 and p(TMC)8LiClO4 electrolytes. These prototype devices present an overall transmittance of ~75% in their bleached state and after coloration 40.5 and 52.5% respectively. These devices also show memory effect and an optical density considered satisfactory for some electrochromic applications.

Abstract: The purpose of this work is to present in-depth electrical characterization on transparent TFTs, using zinc oxide produced at room temperature as the semiconductor material. Some of the studied aspects were the relation between the output conductance in the post-pinch-off regime and width-to-length ratios, the gate leakage current, the semiconductor/insulator interface traps density and its relation with threshold voltage. The main point of the analysis was focused on channel mobility. Values extracted using different methodologies, like effective, saturation and average mobility, are presented and discussed regarding their significance and validity. The evolution of the different types of mobility with the applied gate voltage was investigated and the obtained results are somehow in disagreement with the typical behavior found on classical silicon based MOSFETs, which is mainly attributed to the completely different structures of the semiconductor materials used in the two situations: while in MOSFETS we have monocrystalline silicon, our transparent TFTs use poly/nanocrystalline zinc oxide with grain sizes of about 10 nm.

Abstract: In this work we studied the influence of the power density of hydrogen plasma on electrical and optical properties (Hall mobility, free carrier concentration, sheet resistance, optical transmittance and a.c. impedance) of indium zinc oxide films, aiming to determine their chemical stability. This is an important factor for the optimization of amorphous/nanocrystalline p-i-n hydrogenated silicon (a/nc-Si:H) solar cells, since they should remain chemically highly stable during the p layer deposition. To perform this work the transparent conductive oxide was exposed to hydrogen plasma at substrate temperature of 473 K, 87 Pa of pressure and 20 sccm of hydrogen flow. The results achieved show that IZO films were reduced for all plasma conditions used, which leads mainly to a decrease on films transmittance. For the lowest power density used in the first minute of plasma exposition the transmittance of the IZO films decreases about 29%.

Abstract: In this work, HfO2 was deposited by r.f. sputtering at room temperature and then annealed for different times at 200°C in a forming gas atmosphere. After annealing for 2 hours the HfO2 layers present a reduction on the flat band voltage of about 1 V, relatively to the as deposited film, decreasing from -2.23V down to -1.28 V. This means an improvement of the interface properties and a reduction on the oxide charge density from 1.33×1012 cm-2 to 7.62×1011 cm-2. The dielectric constant reaches a maximum of 18.3 after 5h annealing due to film’s densification. When annealing for longer times such as 10h a small degradation of the electrical properties is observed. After 10h annealing the dielectric constant, flat band voltage and fixed charge density are respectively, 14.9, -2.96 V and 1.64 ×1012 cm-2 and the leakage current also increases due to film’s crystallization.

Abstract: In this work, the relation between oxidant/monomer ratio and the electrical conductivity of polypyrrole was studied using different ratios. We achieved a maximum value for electrical conductivity of 7.5 S/cm for a ratio of 2:1. We also developed a chemical dip-coating process to produce the cathode layer in tantalum capacitors. We obtained capacitances of about 80 µF after 8 cycles using the sequence Monomer/Oxidant.

Abstract: In this work metal induced crystallization (MIC) using nickel (Ni) was employed to obtain poly-Si by crystallization of amorphous films for application as active layer in TFTs. Ni layers with thicknesses of 0.5 nm, 1 nm and 2 nm were used to crystallize the silicon. The TFTs were produced with a bottom gate configuration using a multi-layer Al2O3/TiO2 insulator produced by atomic layer deposition (ALD) as gate dielectric. The best performances of the TFT produced were obtained when using very thin Ni layers for the crystallization. This is attributed to a lower metal contamination and to the enhancement of grain size, as a result of the lower nucleation density achieved, when using the thinnest Ni layer. Devices that exhibit effective mobility of 45.5 cm2V-1s-1 and an on/off ratio of 5.55×104 were produced using a 0.5 nm Ni layer to crystallize the active channel area.

Abstract: A series of amorphous silicon carbide films were prepared by plasma enhanced chemical vapor deposition technique on (100) silicon wafers by using methane, silane, and hydrogen as reactive resources. A very thin (around 15 Å) gold film was evaporated on the half area of the a- SiC:H films to investigate the metal induced crystallization effect. Then the a-SiC:H films were annealed at 1100 0C for 1 hour in the nitrogen atmosphere. Fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (XRD), and scanning electron microscopy (SEM) were employed to analyze the microstructure, composition and surface morphology of the films. The influences of the high temperature annealing on the microstructure of a-SiC:H film and the metal induced metallization were investigated.