Papers by Author: Sophia Arnauts

Abstract: In this atomic-scale study on technologically relevant group IV semiconductors, Ge and SiGe, we relate surface chemistry, in particular the nature of surface oxides, to wet etching kinetics. ICP-MS quantification of Ge in HCl solution containing H₂O_­2 as the oxidizing agent showed that the Si bulk concentration strongly impacted the etching kinetics. Post operando synchrotron XPS provided insight into the surface oxide chemistry involved in the etching process: a non-homogeneous porous layer with a depletion of Ge components at the outer surface due to pull out effects.

Abstract: In this work the etching kinetics of Ge (100) is studied in acidic solutions containing and oxidizing agent. It is shown that the etch rate in the low etch-rate range is controlled by the concentration of the acid, oxidizing agent and the hydrodynamics of the system. The surface termination during etching has strong impact on the etching kinetics. Finally, we discuss the stability of the Ge (100) surface in water and relate this to the low solubility of the Ge suboxides

Abstract: Compound semiconductors based on group III and V elements of the periodic system have high charge carrier mobility and are, therefore, candidates for channel material in future CMOS devices [1]. In order to design wet chemical solutions that lead to appropriate surface pre-conditioning and allow for nanoscale processing and minimal substrate loss, a thorough understanding of the interactions between the substrate and the chemical solutions is needed and the basic etching mechanisms needs to be resolved. The focus of this research is on InP in acidic solutions. ESH aspects are also considered.

Abstract: In this work, the compatibility of InP and InGaAs in cleaning solutions commonly used in semiconductor manufacturing is investigated. Aqueous oxidizing cleans should be avoided as the substrates dissolve rapidly. Low pH solutions may impose some serious ES&H issues due to hydride evolution occurring upon acidic hydrolysis of the III-V material. However, acidic solutions are very efficient to remove the native oxide from the substrate. Complete oxide free surfaces are not achieved after wet cleaning due to the rapid oxidation of these materials in the atmosphere.

Abstract: The local particle removal efficiency (PRE) of nano particles in megasonic cleaning experiments is studied. This approach makes it possible to quantify non uniform cleaning effects over the wafer and to look into the dynamics of particle removal at different areas on the wafer. A direct correlation between PRE and megasonic induced damage of device structures demonstrates that a considerable amount of damage is already formed at less efficiently cleaned areas of the wafer.

Abstract: With the continuous shrinkage of critical sizes in semiconductor manufacturing, nano-particles smaller than 100-nm are becoming a potential threat to devices in chips. Storage of wafers contaminated during process steps often results in a decrease of particle removal efficiency in subsequent clean, a phenomenon referred to as aging. In this work, the influence of aging on the removal of silica and silicon nitride nano-particles from hydrophilic Si wafers was studied for different storage conditions. Trends observed for aging as a function of particle size and for different tools indicated that aging will become an issue for critical cleans where substrate etching must be kept very low and the physical component of the clean must be decreased to prevent damage to fine structures. Controlling the relative humidity during storage helped in lowering the effect of aging.

Abstract: Cleaning of nanoparticles (< 50nm ) is becoming a major challenge in semiconductor manufacturing and the future use of traditional methods, such as megasonic cleaning, is questioned. In this paper the capability of megasonic cleaning to remove nanoparticles without inflicting damage to fragile structures is investigated. The role of dissolved gas in cleaning efficiency indicates that cavitation is the main cleaning mechanism. Consequently gas mass-balance analyses are needed to optimize the performance of cleaning tools. When gas is dissolved in the cleaning present tools can remove nanoparticles down to about 30 nm using dilute chemistries at low temperature. Ultimate performance is limited by cleaning uniformity, which depends on tool design and operation. However no tool reached the target of high particle removal efficiency andlow damage. Significantly lower damage could only be obtained by decreasing the power, at the cost of a lower cleaning efficiency for nanoparticles. The development of damage-free megasonic is discussed.

Abstract: In this paper, a single wafer linear IPA vapour based vertical drying technique is presented. Using salt residue tests the performance of this technique is evaluated and compared to spin drying. The equivalent film thickness of evaporating liquid is below 0.05µm for blanket wafers, which is two orders of magnitude less than with spin drying. It is also shown that the presence of surface topography (200nm high TEOS features on Si covered with a chemical oxide) does not significantly influence the drying performance. A study of the process window shows that for the setup evaluated in this work best performance is achieved when the IPA/N2 flow rate is above 20 liters per minute and the drying speed is below 8 mm/s. With a manual prototype already very good particle performance is demonstrated.