Influence of the Cutting Parameters on the Surface Roughness when Machining Hardened Steel with Ceramic and PCBN Cutting Tools

Gabriel Constantin Benga; Ionel Dănuț Savu; Bebe Adrian Olei

doi:10.4028/www.scientific.net/AEF.13.19

Paper Titles

Foreword, Committees and Sponsors

Composite Compacts of Fe/Fe₃O₄ Type Obtained by Mechanical Milling-Sintering-Annealing Route
p.3

Nanocrystalline/Nanosized Fe₃O₄ Powder Obtained by Mechanosynthesis
p.9

Green Composites Based on Kenaf Fibers
p.15

Influence of the Cutting Parameters on the Surface Roughness when Machining Hardened Steel with Ceramic and PCBN Cutting Tools
p.19

An Estimate of Thermo-Physical Changes in Hybrid Basalt/Glass Fibres Reinforced Polymer Composites
p.23

Research of the Fe₂O₃ Powder Granulation Effect on BaFe₁₂O₁₉ Firing Temperature
p.29

Effect of Process Control Agents on the FeSiB Powder Amorphisation by Wet Mechanical Alloying
p.37

Fracture Analysis of Porous P/M Iron Based Materials
p.42

HomeAdvanced Engineering ForumAdvanced Engineering Forum Vol. 13Influence of the Cutting Parameters on the Surface...

Influence of the Cutting Parameters on the Surface Roughness when Machining Hardened Steel with Ceramic and PCBN Cutting Tools

Abstract:

The paper presents the influence of various cutting regimes on the surface roughness, when a hardened bearing steel has been machined using both ceramic and PCBN cutting tools. There were used different cutting conditions varying cutting speed, feed rate and depth of cut in order to determine the influence of each cutting parameter on the surface finish.

By email View Pdf

You have full access to the following eBook

Read eBook

Info:

Periodical:

Advanced Engineering Forum (Volume 13)

Pages:

19-22

DOI:

https://doi.org/10.4028/www.scientific.net/AEF.13.19

Citation:

Cite this paper

Online since:

June 2015

Authors:

Gabriel Constantin Benga*, Ionel Dănuț Savu, Bebe Adrian Olei

Keywords:

Ceramic, Cutting Parameters, Hard Turning, PCBN, Surface Roughness

Export:

RIS, BibTeX

Permissions:

Creative Commons CC BY 4.0

Citation:

* - Corresponding Author

References

[1] Saini, S., Ahuja, I.S., Sharma, V.S.: Influence of Cutting Parameters on Tool Wear and Surface Roughness in Hard Turning of AISI H11 Tool Steel using Ceramic Tools. Int. Journal of Precision Engineering and Manufacturing, Vol. 13, No. 8, pp.1295-1302, Springer, DOI 101007/s12541-012-0172-6, (2012).

DOI: 10.1007/s12541-012-0172-6

Google Scholar

[2] Klimenko, S.A., Mukovoz, Y.U., Polonsky, L.G. Advanced ceramic tools for machining applications, Key Engineering Materials , vol. 114, Zurich, (1996).

Google Scholar

[3] Jeffrey, D., Shreyes, N.M. Effect of cutting edge geometry and workpiece hardness on surface residual stresses in finish hard turning of AISI 52100 steel, MED. Vol10, Manufacturing Science and Engineering, ASME 10, pp.805-979, (1999).

DOI: 10.1115/imece1999-0743

Google Scholar

[4] Winands, N. Hartdrehen aus der Umformwarme geharteter Walzlageringe, Dissertation, RWTH, Aachen, (1996).

Google Scholar

[5] Chou, Y.K., Evans, C.J., Barash, M.M. Experimental investigation on cubic boron nitride turning of hardened AISI 52100 steel, Journal of Materials processing Technology, vol 134, pp.1-9, (2003).

DOI: 10.1016/s0924-0136(02)00070-5

Google Scholar

[6] Konig, W., Berktold, A., Koch, K.F. Turning versus grinding: a comparison of surface integrity aspects and attainable accuracies, Annals of the CIRP, 42(1), , pp.39-43, (1993).

DOI: 10.1016/s0007-8506(07)62387-7

Google Scholar

[7] Grzesik, W.: Wear of ceramic tools in hard machining, Journal of Achievements in Materials and Manufacturing Engineering, Vol. 26, Issue 2, pp.127-130, (2008).

Google Scholar