The Possibility of Visualizing Temperature Fields Using Digital Holographic Interferometry

Abstract:

The presented paper compares results of measured temperature fields achieved by digital holographic interferometry (DHI) and hot wire anemometry. It shows the possibility of using holographic interferometry for the visualization of temperature fields in periodically moving fluids. The measurement of temperature fields in moving fluids has many inherent difficulties. The usage of point temperature measurement methods, such as Constant Current Anemometry (CCA), is limited to frequencies up to 3000 Hz. This frequency should be the limiting factor for using CCA in fluids when a rapid change of temperature occurs. This shortcoming of CCA measurements could be overcome through the use of optical methods such as digital holographic interferometry. It is necessary to employ a special holographic setup with double sensitivity instead of the commonly used Mach-Zehnder type of holographic interferometer in order to attain parameters sufficient for the studied case. This setup is not as light-efficient as the Mach-Zehnder type but has double sensitivity. The special technique of acquiring and phase averaging the results from holographic interferometry is presented. The paper also shows the first results of an evaluated 3D temperature field.

• Periodical: Applied Mechanics and Materials (Volumes 284-287)
• Pages: 988-995
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.284-287.988
• Online since: January 2013
• Authors: Tomáš Vít, Vít Lédl, Roman Dolecek, Pavel Psota
• Keywords: Holographic Interferometry, Hot-Wire Anemometry, Pulsatile Flow, Temperature Measurement

References

[1] U. Schnars and W. Jueptner: Digital Holography. Berlin, Springer, (2005).

[2] T. Vít and V. Lédl: Identification of the temperature field in pulsatile impinging flow, AIP Conference Proceedings, 1281 (2010), pp.135-138.

[3] R. Dolecek, V. Ledl, V. Kopeck, P. Psota, J. Vaclavik and T. Vit, Prospects of digital holographic interferometry in heat transfer measurement, Experimental Fluid Mechanics 2009, Liberec, Czech Republic (2009)

[4] B.L. Smith and A. Glezer: The formation and evolution of synthetic jets, Phys. Fluids, 10, 2281–2297, (1998)

DOI: 10.1063/1.869828

[5] B.L. Smith, A. Glezer: Jet vectoring using synthetic jets, J. Fluid Mech., 458, (2002) p.1–34.

DOI: 10.1017/s0022112001007406

[6] Z. Trávníček, and V. Tesař: Annular synthetic jet used for impinging flow mass–transfer, Int. J. Heat Mass Transfer, 46, 3291–3297, (2003)

DOI: 10.1016/s0017-9310(03)00119-4

[7] D. S. Kercher, J.-B. Lee, O. Brand, M.G. Allen and A. Glezer: Microjet cooling devices for thermal management of electronics, IEEE Transactions on Components and Packaging Technologies, 26, (2), (2003), p.359–366.

DOI: 10.1109/tcapt.2003.815116

[8] Z. Trávníček, T. Hyhlík and F. Maršík: Synthetic jet impingement heat/mass transfer, Journal of Flow Visualization and Image Processing, Vol. 13, (2006)

[9] Z. Trávníček, J. Vogel, T. Vít and F. Maršík: Flow field and mass transfer experimental and numerical studies of a synthetic impinging jet. In the 4th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics – HEFAT2005, Cairo, Egypt, No. ZT4, (2005)

[10] B.L. Smith and G.W. Swift: A Comparison Between Synthetic Jets and Continuous Jets, Exp. Fluids, Vol. 34 (2003), pp.467-472.

DOI: 10.1007/s00348-002-0577-6

[11] T. Kreis: Handbook of Holographic Interferometry: Optical and Digital Methods. Berlin: Wiley, (2004).