Dynamic Testing at High Strain Rates of AZ31 Magnesium Alloys on SHPB Equipment

Xu Qing Chang; Tie Hua Ma

doi:10.4028/www.scientific.net/AMM.303-306.2648

Paper Titles

A Comparative Study of Fatigue Performance to Resist Reflective Cracking among three Different Stress-Absorbing Materials
p.2625

Research into the Preparation and Performance of PP-G-DL411 Compatibilizer and PP-G-DL411/GF/ PP Composites
p.2636

The Synthesis and Characterization of 1-methyl-3-butyl imidazole Tetrafluoroborate
p.2640

Investigation of Magnetic Behavior of SmCo₅/SmCo₂ Nanocrystalline Magnets
p.2644

Dynamic Testing at High Strain Rates of AZ31 Magnesium Alloys on SHPB Equipment
p.2648

Torsion-Dependent Circular Magnetization in Fe-Based Amorphous Wire
p.2652

Effect of Surface Elasticity on Scattering of Plane P-Waves by an Elastic Half-Plane with a Semi-Cylindrical Cavity
p.2656

Effects of Surface Elasticity on Scattering of P Waves by an Elastic Half-Plane with a Nanosized Semi-Cylindrical Inclusion
p.2661

One-Step Hydrothermal Controlled Synthesis of HgTe Nanorods
p.2667

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vols. 303-306Dynamic Testing at High Strain Rates of AZ31...

Dynamic Testing at High Strain Rates of AZ31 Magnesium Alloys on SHPB Equipment

Abstract:

The mechanical behaviour of as-cast AZ31 Mg alloy has been investigated at strain rates up to 2.0×103s-1. Dynamic tests were carried out at room temperature using a Split Hopkinson Pressure Bar (SHPB) apparatus. Microstructural characteristic were analysed by Image MAT A1 optical microscopy. The results demonstrated that AZ31 Mg alloy exhibited obvious yield phenomena and strain hardening behaviour at high strain rates. The basically same curvature of stress-strain curves exhibited an similar strain hardening rate. The dynamic yield strength changes little and the peak stress increases with the strain rates. An examination by optical microscopy after high strain rate deformation reveals the occurrence of twinning and twin area percentage increases with the strain rate increasing.

You might also be interested in these eBooks

Sensors, Measurement and Intelligent Materials

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volumes 303-306)

Pages:

2648-2651

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.303-306.2648

Citation:

Cite this paper

Online since:

February 2013

Authors:

Xu Qing Chang, Tie Hua Ma

Keywords:

AZ31, Dynamic Mechanical Properties, High Strain Rate, Microstructure

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] Mark P. Staiger, Alexis M. Pietak, Jerawala Huadmai, George Dias. Biomaterials 27 (2006) 1728–1734.

DOI: 10.1016/j.biomaterials.2005.10.003

Google Scholar

[2] Nuno Peixinho*, Claudia Doellinger. Materials Research. 2010; 13(4): 471-474.

Google Scholar

[3] B. Li, S. Joshi, K. Azevedo, E. Ma, K.T. Ramesh, R.B. Figueiredo, T.G. Langdon. Materials Science and Engineering A 517 (2009) 24–29.

Google Scholar

[4] Pingli Mao, Zheng Liu, Changyi Wang. Materials Science and Engineering A 539(2012)13-21.

Google Scholar

[5] Valle J and Ruano O. Scripta Materialia. 2006; 55: 775-778.

Google Scholar

[6] I. Ulacia, C.P. Salisbury, I. Hurtado, M.J. Worswick. J Mater Process Technol Vol. 211 (2011), pp.830-839.

Google Scholar

[7] I. Ulacia, N.V. Dudamell, F. Ga´lvez, S. Yi, M.T. Pe´rez-Prado, I. Hurtado. Acta Materialia 58 (2010) 2988–2998.

DOI: 10.1016/j.actamat.2010.01.029

Google Scholar

[8] Christiian J W, Mahajan S．Deformation Twinning[J]．Progress in Materials Science, 1995, 139: 301-311.

Google Scholar

[9] M.A. Meyers, O. Vöhringer, V.A. Lubarda, Acta Mater. 49 (2001) 4025–4039.

Google Scholar

[10] Watanabe, H., Ishikawa, K., Mukai, T., 2007. Key Eng. Mater. 340–341, 107–112.

Google Scholar