Surface Modification of SKD 61 by Electrical Discharge Coating (EDM/EDC) with Multilayer Cylindrical Electrode and Jatropha Curcas as Dielectric Fluid

Abstract:

Electrical Discharge Machining (EDM) is the most extensive non-conventional material removal processes used. In recent years, EDM researchers have been explore several sparking efficiency improvement methods including some unique experimental concepts that begin from the EDM traditional sparking phenomenon. This paper reports the use of layered cylindrical electrodes combined with jatropha curcas as dielectric fluid which is not widely used in the EDM process. The results are compared with the EDM process using kerosene dielectric fluid and single electrode (conventional). Dielectric fluid jatropha curcas is expected to substitute the commonly used dielectric fluid. Dielectric strength was tested by the impulse method. Furthermore, the EDM process is measured using surface roughness and microhardness of white layer values at various cutting conditions on the material SKD 61 as an indicator. The highest value of white layer hardness using jatropha curcas dielectric fluid is provided by three layers of electrodes, whereas the lowest is resulted of two layers of electrodes. Meanwhile, the use of kerosene dielectric fluid, the highest hardness value is achieved by two layers of electrodes, and the lowest is produced by three layers of electrodes. This study shows that jatropha curcas dielectric fluid is potential to be used in the EDM process since it produces a smoother surface and higher white layer hardness value.

• Periodical: Applied Mechanics and Materials (Volume 319)
• Pages: 96-101
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.319.96
• Online since: May 2013
• Authors: Dedi Priadi, Triyono Triyono*, Eddy S. Siradj, Winarto Winarto
• Keywords: Dielectric Fluid, Electric Discharge Machining (EDM), Jatropha Curcas, Layered Electrode, Microhardness, Surface Roughness (SR), White Layer

References

[1] K.H. Ho and S. T. Newman, "State of the art electrical discharge machining (EDM)", International Journal of Machine Tools & Manufacture, 2003.

DOI: 10.1016/s0890-6955(03)00162-7

[2] S Kumar1,R Singh, T P Singh, and B L Sethi, "Comparison of material transfer in electrical discharge machining of AISI H13 die steel", Journal Mechanical Engineering Science, JMES1227 © IMechE 2009, Vol. 223 Part C

DOI: 10.1243/09544062jmes1227

[3] Han-Ming Chow, Lieh-Dai Yang, Ching-Tien Lin, Yuan-Feng Chen,"The used of SiC powder in water as dielectric for micro-slit EDM machining", Journal of Materials Processing Technology, 2007.

DOI: 10.1016/j.jmatprotec.2007.04.130

[4] P. Pecas, E. Henriques, " Electrical discharge machining using simple and powder-mixed dielectric: The effect of the electrode area in the surface roughness and topography", Journal of Materials Processing Technology, 200, 2008.

DOI: 10.1016/j.jmatprotec.2007.09.051

[5] Xiaohai Li et al., "Research on surface modification Technique by EDM", Advanced Materials Research Vols. 154-155, 2011.

[6] Yu-Lung Hwang, Chia-Lung Kuo, Shun-Fa Hwang, 'The coating of TiC layer on the surface of nickel by electric discharge coating (EDC) with a multi-layer electrode", Journal of Materials Processing Technology, 210, 2010.

DOI: 10.1016/j.jmatprotec.2009.11.013

[7] Y.H. Liu, R.J. Ji, X.P. Li, L.L. Yu, H.F. Zhang, Q.Y. Li, "Effect of machining fluid on the process performance of electric discharge milling of insulating Al2O3 ceramic", International Journal of Machine Tools & Manufacture 48 (2008) 1030–1035.

DOI: 10.1016/j.ijmachtools.2007.12.011

[8] Kun Ling Wu,. Biing Hwa Yan, Fuang Yuan Huang, Shin Chang Chen, "Improvement of surface finish on SKD steel using electro-discharge machining with aluminium and surfactant added dielectric", International Journal of Machine Tools & Manufacture 45 (2005) 1195–1201.

DOI: 10.1016/j.ijmachtools.2004.12.005

[9] D Kanagarajan , R Karthikeyan, K Palanikumar, and P Sivaraj, " Influence of process parameters on electric discharge machining of WC/30%Co Composites", Proc. IMechE Vol. 222 Part B: J. Engineering Manufacture, 2008.

DOI: 10.1243/09544054jem925

[10] Mohd Amri Lajis, H.C.D. Mohd Radzi, A.K.M. Nurul Amin, "The Implementation of Taguchi Method on EDM Process of Tungsten Carbide", European Journal of Scientific Research, 2009.