Optimisation of Single Edge Tools Exploitation Process

Abstract:

Paper show possibilities to optimization of exploitation process of single edge tools. It decrease cost of machining using optimizing the use of the cutting edge. This possibility was presented for single edge tools in oblique and orthogonal cutting. In oblique cutting was presented optimizing the use of the cutting edge by partially exchange of active section of the cutting edge. It is shown for straight edges. Presents model of special tool and result of made experiments, which shows possibilities to increase tool life. Second presented possibilities is orthogonal cutting with round insert. Presented results of calculations of number cutting edges from one round insert by optimizing the use of the cutting edge. For orthogonal cutting was used normal market construction tools for round inserts. Presents first results of surface roughness for tools with worn up cutting edge and rotate for exchange this worn up fragment of cutting edge. In this case number of edges cutting insert increase many times. This can many times reduce the cost of tools in cutting especially in turning.

• Periodical: Applied Mechanics and Materials (Volume 332)
• Pages: 431-436
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.332.431
• Online since: July 2013
• Authors: Tadeusz Mikolajczyk, Łukasz Romanowski
• Keywords: Edge Wear, Oblique Cutting, Orthogonal Cutting, Single Edge Tool, Tool Life

References

[1] Vicev S. V.: Issledowanije processa na razanie z sirki bezverchovi nożove z naklonnoj rezuscie rieb. Investigation of oblique cutting process with single straight edge. Ruse, Bulgaria, VTV, 1981 (in bulgarish)

[2] Cichosz P.: Narzedzia skrawajace. Cutting tools. Warszawa, WNT, 2006 (in polish)

[3] Latos H., Mikolajczyk T.: Badanie chropowatosci powierzchni przy toczeniu wzdluznym stali 1H18N9T ostrzami jednokrawedziowymi o prostoliniowej krawedzi skrawajacej. Investigation of surface roughness in longitudinal turning of 1H18N9T with single edge tools of straight edge. Prace Naukowe Instytutu TBM Politechniki Wroclawskiej, 27, Wroclaw, (1981) (in polish)

[4] Latos H., Mikolajczyk T.: Zwiekszenie okresu trwania ostrzy jednokrawędziowych. Increase of tool life single edges. III Intersympozjum, Badania narzędzi, Kraków, (1988) (in polish)

[5] Noz tokarski zwlaszcza do obrobki wykanczajacej. Turning tool especially for finishing. Zgl. Patent. ATR Bydgoszcz, tworca: T. Mikolajczyk, nr P-263554, data zgloszenia 31.12.1986 (in polish)

[6] Sposob zwiekszenia trwania ostrzy jednokrawędziowych. Increase of life time of cutting edges. Zgl. patent. ATR Bydgoszcz, tworca: T. Mikolajczyk, nr P-268078, data zgloszenia 24.09.1987 (in polish)

[7] Mikolajczyk: T. Recyrkulacja plytek wieloostrzowych w skrawaniu jednokrawedziowym Recilculation cutting inserts in single edge cutting. Inznieria i Aparatura Chemiczna, nr 3, (2006), pp.57-59 (in polish)

[8] Grzesik W, Zak K.: Investigations of surface textures produced by oblique machining of different workpiece materials. Archives of Material Sciences and Engineering. Vol. 52, Issue 1, (2011)

[9] Mikolajczyk T.: Skrawanie ortogonalne z recylkulacja ostrza o luku krawedzi. Orthogonal cutting with recilculation of round inserts. Inzynieria i Aparatura Chemiczna, nr 4, (2008), pp.53-54 (in polish)

[10] Mikolajczyk T.: Odtwarzanie wlasnosci skrawnych ostrza z krawedzia skrawajaca o luku okregu. Restoration of cutting properties of round inserts. Inzynieria i Aparatura Chemiczna, nr 5, (2010), pp.81-82 (in polish)

[11] Mikolajczyk T.: Edge properties restoration in cutting with single edge tool. Academic Journal of Manufacturing Engineering, Vol. 11, Issue 1, 2013 (submitted to print)