A 3-DOF Controlled, High-Speed, High-Precision Local Actuator for Micro Electrical Discharge Machining

Abstract:

In conventional Electrical Discharge Machining (EDM), the speed and accuracy are limited by probability and efficiency of the electrical discharges. To improve the machining speed and accuracy, we developed a high-speed, high-precision, 3-DOF controlled local actuator. For the actuator, a voice coil motor type of magnetic bearing having a positioning stroke of a few millimeters is used to control the motion of an electrode in the thrust direction in order to speedily maintain a suitable distance from the workpiece. Moreover, two piezoelectric devices having high response speed and high precision are used to achieve the vibration of the electrode in the radial directions to immediately remove the debris between the electrode and the workpiece. The positioning performance of the actuator was evaluated through experiments, and the experimental results show that the actuator possesses a positioning resolution of the order of micrometer, a bandwidth greater than 120Hz and a positioning stroke of 2mm.

• Periodical: Applied Mechanics and Materials (Volumes 423-426)
• Pages: 2821-2824
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.423-426.2821
• Online since: September 2013
• Authors: Xiao You Zhang, Tomohiro Ishizuka, Kouki Uchiyama
• Keywords: Actuator, Electrical Discharge Machining (EDM), Magnet, Piezoelectric Device

References

[1] M. Kunieda, B. Lauwers, K. P. Rajurkar and B. M. Schumacher: Advancing EDM through Fundamental Insight into the Process. Annals of the CIRP, Vol. 54 (2005), No. 2, p.599.

DOI: 10.1016/s0007-8506(07)60020-1

[2] T. Masuzawa: State of Art of Micromachining. Annals of the CIRP, Vol. 49 (2000), No. 2, p.473.

[3] Y. Imai, A. Satake, A. Taneda and K. Kobayashi: Improvement of EDM Machining Speed by Using High Frequency Response Actuator. Int. J. Electr. Mach., (1996), No. 1, p.21.

[4] T. Masuzawa, K. Tanaka and M. Fujino: Study on the High Speed Machining by EDM Using a Moving Coil Head Type Feed Control. In: Proceedings of the 19th International MTDR Conference, (1978), p.543.

DOI: 10.1007/978-1-349-81412-1_65

[5] X. Zhang, T. Shinshi, G. Kajiwara, A. Shimokohbe, Y. Imai, H. Miyake and T. Nakagawa: A 5-DOF Controlled Maglev Local Actuator and its Application to Electrical Discharge Machining. Precision Engineering, Vol. 32 (2008), No. 4, p.289.

DOI: 10.1016/j.precisioneng.2007.10.003

[6] H. Huang, H. Zhang, L. Zhou and H. Y. Zheng: Ultrasonic Vibration Assisted Electro-discharge Machining of Microholes in Nitinol. Journal of Micromechanics and Microengineering, Vol. 13 (2003), No. 5, p.693.

DOI: 10.1088/0960-1317/13/5/322

[7] T. Endoa, T. Tsujimoto and K. Mitsui: Study of Vibration-assisted Micro-EDM. -The Effect of Vibration on Machining Time and Stability of Discharge. Precision Engineering, Vol. 32 (2008), No. 4, p.269.

DOI: 10.1016/j.precisioneng.2007.09.003