The Use of dsPIC in the Identification of Inertia Moment and Friction Coefficient of PMS and DC Motors

Abstract:

In the present study, the inertia moment and friction coefficient of direct current (DC) and permanent magnet synchronous (PMS) motors were calculated. Retardation experiment was carried out to calculate these values, and current, voltage and rotation values of the motor were calculated with the help of sensors. The measurement results were read with the help of a card designed using dsPIC30F4013, a high-performance digital signal controller. Power and torque values were calculated using the data transferred into the computer. Graphs showing power-velocity and velocity-time were drawn through the use of the values that were measured and calculated. Power-time graph was obtained by using these two graphs. To be able to carry out numerical procedures using the power-time graph created, curve fitting method in MATLAB was used, and mathematical expression of the graph was obtained. The kinetic energy stored in the motor was calculated using the mathematical expression mentioned, and the inertia moment was found using this value. The friction coefficient was calculated using the torque equation for stationary running of the motor at rated speed. The results of the simulation carried out in MATLAB by using the calculated coefficients and those of the experiment were compared.

• Periodical: Applied Mechanics and Materials (Volumes 446-447)
• Pages: 1197-1201
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.446-447.1197
• Online since: November 2013
• Authors: Hakan Terzioğlu, Fatih Alpaslan Kazan, Murat Selek*
• Keywords: dsPIC30F4013, Friction Coefficient (FC), Inertia Moment, Retardation Experiment

References

[1] F. Andoh: Moment of inertia identification using the time average of the product of torque reference input and motor position. IEEE Trans. On Power Elect., 22(6), (2007), pp.2534-2542.

DOI: 10.1109/tpel.2007.909309

[2] S. Samer and R. A. Kaed-Bey: Parameter identification of a dc motor: an experimental approach, Electronics, Circuits and Systems, The 8th IEEE Inter. Conf. (2001), vol. 2 pp.981-984.

DOI: 10.1109/icecs.2001.957638

[3] J-W. Choi, S. -C Lee and H. -G Kim: Inertia identification algorithm for high-performance speed control of electric motors. IEE Proc. -Electr. Power Appl., 153(3), (2006), pp.379-386.

DOI: 10.1049/ip-epa:20050360

[4] I. Awaya, Y. Kato, I. Miyake, and M. Ito: New motion control with inertia identification function using disturbance observer, in Proc. Int. Conf. Ind. Electronics, Control, Instrumentation, Autom., San Diego, CA, (1992), vol. 1, p.77–81.

DOI: 10.1109/iecon.1992.254601

[5] N. Kim, H. Moon, D. Lee, and D. Hyun: Inertia identification for the speed observer of the low speed control of induction machines, in IEEE Ind. Appl. Conf. 30th IAS Annu. Meeting, Orlando, FL, vol. 3, (1995) p.1938–(1943).

DOI: 10.1109/ias.1995.530547

[6] K. Lee, J. Song, I. Choy, and J. Yoo: An inertia identification using ROELO for low speed control of electric machine, in Proc. 18th Annu. Appl. Power Electron. Conf., Miami Beach, FL, vol. 2, (2003), p.1052–1055.

DOI: 10.1049/ip-epa:20031009

[7] K.B. Lee, J.Y. Yoo, J.H. Song and I. Choy: Improvement of low speed operation of electric machine with an inertia identification using ROELO. IEE Proc. -Electr. Power Appl., 151(1). (2004) pp.116-120.

DOI: 10.1049/ip-epa:20031009

[8] Gopal K. Dubey: Fundamentals of Electrical Drives, 2th Ed. pp.17-18 Alpha Science Int. Ltd.

[9] F. A. Kazan: Kalıcı Mıknatıslı Senkron Motorun Kontrolü, M.S. Thesis, Dept. Electric-Electronic Eng., Selcuk Univ., Konya, Turkey, (2009).