The Cutting Tool Wear of the Cutting Tool Part of the Cast Iron GTW 35-04 during Drilling

Jozef Jurko

doi:10.4028/www.scientific.net/AMM.470.589

Paper Titles

Vertical Vibration Characteristics Analysis of Stand Rolls System in Six-Roll Cold Tandem Mill
p.572

Experimental Study on the Surface Roughness of 40Cr by Ultrasonic Finishing Machining
p.577

Life Prediction of Two Rotor Steels under Creep-Fatigue Interaction at Elevated Temperature
p.581

The Analysis of Processing Factors for Electro-Arc Machining
p.585

The Cutting Tool Wear of the Cutting Tool Part of the Cast Iron GTW 35-04 during Drilling
p.589

Analysis of Dynamic Characteristics of the Dual Ball Screw-Driven Linear Feed System in Z Direction
p.593

Study on Application of the Mine Anti-Impact and Energy-Absorption Device
p.598

A Study on the Effect of Driver Model Parameters on the Performance of Driver-Vehicle-Road Closed-Loop System
p.604

A Power Optimization Algorithm for Ad Hoc Networks with Variable Rate Control
p.611

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 470The Cutting Tool Wear of the Cutting Tool Part of...

The Cutting Tool Wear of the Cutting Tool Part of the Cast Iron GTW 35-04 during Drilling

Abstract:

The basic hypothesis of this article focuses on the study changes in the tool wear during drilling of cast iron GTW 35-04. The problem of drilling holes with diameter D=5 to 10 mm resides in the fact that 40 % of these holes do not comply with prescribed requested requirements. This article presents the results of experiments focusing on the study of the damage process in helical drills with diameter d=10.0 mm when drilling into the cast iron GTW 35-04.

You might also be interested in these eBooks

Mechanical Engineering, Materials Science and Civil Engineering II

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 470)

Pages:

589-592

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.470.589

Citation:

Cite this paper

Online since:

December 2013

Authors:

Jozef Jurko*

Keywords:

Cast Iron, Drilling, EDX Analysis, Tool Wear

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] J. Jurko, A. Panda, M. Gajdoš: Accompanying phenomena in the cutting zone machinability during turning of stainless steels. International Journal Machining and Machinability of Materials, Vol. 5, No. 4, pp.383-400, ISSN 1748-5711, (2009).

DOI: 10.1504/ijmmm.2009.026899

Google Scholar

[2] T. Zaborowski: Technologia kszaltowania warstwy wierzchniej. Monografia, Gorzow Wlkp., p.99, ISBN 978-83-932166-8-0, (2011).

Google Scholar

[3] J. Jurko : Verification of surface finish as an indicator of machinability in turning steel X6Cr16Ni10MoTiN, Advanced Materials Research. Vol. 291-294, pp.2987-2990, ISSN 1022-6680, (2011).

DOI: 10.4028/www.scientific.net/amr.291-294.2987

Google Scholar

[4] J. Jurko: The use of TiAlN coated carbide tool when finish drilling of stainless steel X4Cr17Ni8TiN. Applied Mechanics and Materials, Vol. 39, pp.369-374, ISSN 1660-9336, (2010).

DOI: 10.4028/www.scientific.net/amm.39.369

Google Scholar

[5] J. Jurko-M. Džupon-A. Panda-M. Gajdoš-I. Pandová, Deformation of Material Under the Machined Surface in the Manufacture of Drilling Holes in Austenitic Stainless Steel. Chemické listy, Vol. 105, (S), pp.600-602, ISSN 0009-2770, (2011).

Google Scholar

[6] M. Džupon, M. Gajdoš, J. Jurko, M. Ferdinandy, D. Jakubeczyová, Plastic Deformation Around Holes Drilled in Austenitic Steel 1. 4301. Chemické listy, Vol. 105, (S), pp.606-608, ISSN 0009-2770, (2011).

Google Scholar