An Automatic Calibration System for Multimeter Based on Fluke MET/CAL

Nuo Li; Guo Ding Liang; Li Yang; Yun Peng Ji; Song Yang Li

doi:10.4028/www.scientific.net/AMM.644-650.1303

Paper Titles

Control Precision Test Equipment Design of an Anti-Aircraft Gun Servo System
p.1286

Research on Real Performances of Special Optoelectronics Devices Inconformity to their Test Results in Electricity Parameter Detection
p.1290

Research on Signal Detection in Linear Frequency Modulation Model
p.1294

A Study on HT32F1765 MCU-Based in Smart Home Gas Monitoring
p.1298

An Automatic Calibration System for Multimeter Based on Fluke MET/CAL
p.1303

Analysis of the Pitch Diameter Measurement Based on Three-Pin/T-Shaped Probe and Thread Scanner
p.1307

Research of Landmine Detection Using Terahertz Technology
p.1313

Large-Scale Structural Health Monitoring Based on Wireless Sensor Networks
p.1317

The Research of Travel Time Estimation Based on Vehicle License Plate Auto Recognition System
p.1324

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vols. 644-650An Automatic Calibration System for Multimeter...

An Automatic Calibration System for Multimeter Based on Fluke MET/CAL

Abstract:

The calibration process of a digital Multi-meter (DMM) is complicated and tedious. The whole procedure needs to calibrate dozens of test points of several measuring ranges. Usually, the automatic calibration system is used to replace the manual operation. In metrology, the MAT/CAL which is a software produced by Fluke company has been widely used, but it can’t meet our special needs. This article is mainly on the introduction of design method of an automatic calibration system for DMM basing on Fluke MAT/CAL. It describes the setup of hardware, the improvement of ACC file in MAT/CAL and the basic principle of our software.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volumes 644-650)

Pages:

1303-1306

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.644-650.1303

Citation:

Cite this paper

Online since:

September 2014

Authors:

Nuo Li*, Guo Ding Liang, Li Yang, Yun Peng Ji, Song Yang Li

Keywords:

Automatic Calibration System, Digital Multi-Meter (DMM), Fluke MET/CAL Calibration Software, Metrology

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] Rong Zhang, Feng Yang, WeiHua Hu. Design for Agilent 34401A Digital Multi-Meter Automatic Test System [J]. Computer Measurement & Control, 2012, 20(7): 1769-1772.

Google Scholar

[2] Mingliang Chen, Weiping Cai, Jianping Gu. Digital multi-meter automatic calibration system based on LabWindows [J]. Foreign Electronic Measurement Technology, 2012, 11: 61-63.

Google Scholar

[3] Joerg Christian Wolf, Phil Hall, Paul Robinson, Phil Culverhouse. Bioloid based Humanoid Soccer Robot Design, (2007).

Google Scholar

[4] YuPing Mao. Agilent 34401A automatic calibration system based on Fluke MET/CAL and 5700A [J]. Foreign Electronic Measurement Technology, 2009, 28(10): 17-23.

Google Scholar

[5] Xi Fang. Analysis of the automatic calibration system for DMM [J]. Practical Electronics, 2013(2): 102-103.

Google Scholar

[6] MET/CAL User's Guide.

Google Scholar

[7] Xinting Gao, Haibin Jin. Automatic verification & Calibration system of DMM [J]. Aviation Metrology & Measurement Technology, 2001, 21(3): 35-38.

Google Scholar