Estimating Energy Absorbing Performance of Motorcycle Safety Helmet

Abstract:

Motorcyclists’ fatalities are overrepresented in the national statistics for years and the figure is predicted to rise further into the year 2020. In details, head injuries have contributed approximately 60% to the records, despite the use of safety helmets. New helmets performance has been well studied and widely accepted to reduce the head injury risks to motorcyclists by way of maximizing crash energy absorption. However in-service helmets energy management capability and information are limited. Therefore, this work attempts to further explore the knowledge and seek clarification of in-service helmet energy absorbing performance by performing experimental tests relative to standards protocols. A set of in-service helmets were collected from the public through an exchange basis and impact-tested twice per sites, at 4 sites, in accordance to MS1:1996 test protocols. The main data obtained was headform centre of gravity acceleration values, in terms of g. The results indicated that energy absorbing performances of most in-service helmets were able to meet standard requirements, regardless of their service ages. A few samples, however, demonstrated out of tolerance performances especially in the successive impact test at the same sites. Appearance of microcrack in the impact foam may have contributed to these values.

• Periodical: Applied Mechanics and Materials (Volume 663)
• Pages: 574-578
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.663.574
• Online since: October 2014
• Authors: Hamzah Azhar*, Aqbal Hafeez Ariffin, Solah Mohd Syazwan, Shaw Voon Wong
• Keywords: Impact Performance, Motorcycle, Safety Helmet

References

[1] S. Rohayu , S.M.R. Sharifah Alyana, M.M. Jamilah, Motorcycle factsheet, v1, Malaysian Institute of Road Safety Research, (2011).

[2] S. Rohayu, S.V. Wong, Predicting Malaysian road fatalities for year 2020, MRR 06/2012, Kuala Lumpur, (2012).

[3] T.Y. Pang, R.S. Radin Umar, Azhar Abdul Aziz, Harwant Singh, Shahrom Abdul Wahid, Abdul Halim B. Hj. Mansor, Zahari Noor, Mohd Shafie bin Othman, Fatal injuries in Malaysian motorcyclists, Int. Med. Res. J. 3 (1999) 115-119.

[4] A.O.F. Fabio, R.J.A. Sousa, R. Willinger, C. Deck, FEA of helmeted impacts and head injury evaluation with a commercial road helmet, IRCOBI Conf, 2013, pp.431-442.

[5] W.C. Wen, Y.X. Li, D.M. Fu, Study on impact energy absorbing performance of EPS buffer layer of motorcycle helmet, Int. Conf. Mech. Auto. Eng. (2013).

DOI: 10.1109/maee.2013.36

[6] A. Gilchrist, N.J. Mills, Fast fracture of rubber-toughened thermoplastics used for the shells of motorcycle helmets, J. of Mat Sci. 22, 7 (1987) 2397-2406.

DOI: 10.1007/bf01082122

[7] A. Denning, N.J. Mills, The deterioration of thermoplastic motorcycle helmet shells after outdoor exposure, Plastics, Rubb. and Comp. Proc. and App. 18 (1992) 67-77.

[8] H. Azhar, S.V. Wong, Degradation of helmet protective performance: an overview, In: Proc. of Int. Conf Crashworthiness, Washington DC, USA, (2010).

[9] K.S. Tan, Personal communication, Solidgold Helmets Sdn Bhd, (2010).

[10] A. Gale, N.J. Mills, Effect of polystyrene foam liner density on motorcycle helmet shock absorption, Plastics and Rubber Processing and Applications. 5, 2 (1985) 101-108.

[11] Malaysian Standard MS1: 1996, Specifications for protective helmets for vehicle users, 2nd Revision, SIRIM, (1996).

[12] Malaysian Standard MS1: 2011, Protective helmets and visors for vehicle users – specification-part 1: protective helmets, 3rd revision, (2011).

DOI: 10.3403/00099518u

[13] D.S. Liu, C.Y. Chang, C.M. Fan, S.L. Hsu, Influence of environmental factors on energy absorption degradation of polystyrene foam in protective helmets, Eng Failure Anal. 10, 5 (2003) 581–591.

DOI: 10.1016/s1350-6307(03)00040-2