Development of Foot Modules of an Exoskeleton Equipped with Multiple Sensors for Detecting Walking Phase and Intent

Abstract:

This paper presents design and application of foot modules in exoskeleton. Detecting the walking phase and intent is most important data for controlling the wearable exoskeleton. The zero moment point (ZMP) trajectory in the robot foot support area is significant criterion for a stability of the walk. The ZMP is calculated by measured force / torque data and Force / Torque sensor (F/T sensor) can measure that. But, the thick foot module is inconvenient to walking. For such a reason, most foot modules are developed using the film type sensors such as force sensing resistor (FSR), ground contact sensor such as tape switch and so on. In this paper, the foot modules equipped optimal design of 3-axis F/T sensor and ground contact sensor are presented and experimental application of detecting the walking phase using both sensors is introduced.

• Periodical: Applied Mechanics and Materials (Volumes 752-753)
• Pages: 1016-1021
• DOI: https://doi.org/10.4028/www.scientific.net/AMM.752-753.1016
• Online since: April 2015
• Authors: Byoung Jong Son, Yoon Su Baek, Jung Hoon Kim*
• Keywords: Exoskeleton, F/T Sensor, Foot Module, Gait Algorism, Multiple Sensor, Signal Processing, Tape Switch, Walking Phase

References

[1] Institute on Disability. University of New Hampshire, 2010 Annual disability statistics compendium, Rehabilitation Research and Training Center on Disability Statistics and Demographics, (2010).

[2] K. Erbatur, A. Okazaki, K. Obiya, T. Takahashi and A. Kawamura, A Study on the Zero Moment Point Measurement for Biped Walking Robots, IEEE Advanced motion control, (2002).

DOI: 10.1109/amc.2002.1026959

[3] H. Hirohisa, K. Fumio and K. Kenji, Humanoid robotics platforms developed in HRP, Robot. and Auton. Syst. 48 (2004) 165–175.

[4] M. Hirose and K. Ogawa, Honda humanoid robots development. Phil. Trans. R. Soc. A, 365 (2007) 11–19.

[5] Z. Weimin, H. Qiang and J. Dongyong, Mechanical design of a light weight and high stiffness humanoid arm of BHR-03. Robotics and Biomimetics, IEEE Int. Conf. on Digit. Object Identifier. (2009) 1681–1686.

DOI: 10.1109/robio.2009.5420411

[6] L. Jianxi, H. Qiang, Z. Weimin, Y. Zhangguo and L. Kejie, Flexible foot design for a humanoid robot, Automation and Logistics, ICAL 2008, IEEE. Int. Conf. on, 1-3 September, (2008).

DOI: 10.1109/ical.2008.4636375

[7] R.W. Horst, A Bio-Robotic Leg Orthosis for Rehabilitation and Mobility Enhancement, 31st Annu. Int. Conf. of the IEEE. MBS. 2-6 September (2009).

[8] S.K. Banala, S.H. Kim, S.K. Agrawal and J.P. Scholz, Robot Assisted Gait Training With Active Leg Exoskeleton (ALEX), IEEE Transactions on neural systems and rehabilitation engineering, February, 17(1) (2009).

DOI: 10.1109/tnsre.2008.2008280

[9] A.B. Zoss, H. Kazerooni and A. Chu, Biomechanical Design of the Berkeley Lower Extremity Exoskeleton (BLEEX), IEEE/ASME Transactions on mechatronics, April, 11(2) (2006).

DOI: 10.1109/tmech.2006.871087

[10] J.W. Han, Design of Exoskeletal Assistance Robot for Walking and Rehabilitaion, Korean Soc. for Precision Eng. (2011).

[11] S.J.M. Bamberg, A.Y. Benbasat, D.M. Scarborough, D.E. Krebs and J.A. Paradiso, Gait analysis using a shoe-integrated wireless sensor system. IEE Trans. Inform. Technol. Biomed., 12 (2008) 413-423.

DOI: 10.1109/titb.2007.899493

[12] I.P.I. Pappas, M.R. Popovic, T. Keller, V. Diets and M. Morari, A reliable gait phase detection system. IEEE Trans. Neural Syst. Rehab. Eng., 9 (2001) 113-125.

DOI: 10.1109/7333.928571

[13] J.H. Kim, The Design of Foot Module and 3-Axis F/T Sensor for Measuring ZMP of the Exoskeleton. Korean Soc. for Precision Eng. (2013).