Determination of Cutting Forces in Oblique Cutting

A.V. Filippov; E.O. Filippova

doi:10.4028/www.scientific.net/AMM.756.659

Paper Titles

Intellectual Control of Oil and Gas Transportation System by Multidimensional Fuzzy Controllers with Precise Terms
p.633

Adaptive Structural Reconfigurable Algorithms of Control
p.640

Development of a Combined Algorithm for Request Distribution Using Multi-Objective Optimization Methods
p.646

Developing a Procedure for Technical Status Control of a Turbine Compressor Package Blades
p.652

Determination of Cutting Forces in Oblique Cutting
p.659

Object’s Border and Position Allocating in an X-Ray Image
p.667

Benchmark for FFT Libraries
p.673

Imaging Based on Signal from Side-Scan Sonar
p.678

Adaptive Neuro-Fuzzy Recognition Technology Intersecting Objects
p.683

HomeApplied Mechanics and MaterialsApplied Mechanics and Materials Vol. 756Determination of Cutting Forces in Oblique Cutting

Determination of Cutting Forces in Oblique Cutting

Abstract:

This study describes the method of determining cutting force components in oblique turning. The scheme of how the investigations were performed is presented. The characteristic curves of cutting force components vs. thickness of the material removed, tool clearance and tool rake angles are shown. The study presents the data, which have been obtained during the experimental investigations and analytically calculated, on how the cutting forces are subject to changes depending on a cutter angle, cutting depth and feed in oblique turning operations. The analysis of approximation of the experimental results and error check of the theoretical calculations relative to the experimental data are given.

You might also be interested in these eBooks

Mechanical Engineering, Automation and Control Systems

View Preview

Info:

Periodical:

Applied Mechanics and Materials (Volume 756)

Pages:

659-664

DOI:

https://doi.org/10.4028/www.scientific.net/AMM.756.659

Citation:

Cite this paper

Online since:

April 2015

Authors:

A.V. Filippov*, E.O. Filippova

Keywords:

Approximation Results of Experiments, Component Forces, Oblique Turning, Setting System, Skiving Cutter

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] S.A. Klimenko, А.S. Manokhin, Hard oblique, turning. Super-hard Materials, 1 (2009) 58-74.

Google Scholar

[2] W. Grzesik, K. Żak. Investigations of surface textures produced by oblique machining of different workpiece materials. Archives of Materials Science and Engineering, 52 (2011) 46-53.

Google Scholar

[3] W. Grzesik, A real picture of plastic deformation concentrated in the chip produced by continuous straight-edged oblique cutting. Int. J. Mach. Tools Manuf. 31, 3 (1991) 329-344.

DOI: 10.1016/0890-6955(91)90079-i

Google Scholar

[4] S.I. Petrushin, А.V. Filippov, The analysis of the geometry of oblique turning peakless cutters. Treatment of Metals. Technology. Equipment. Tools. 2 (2013) 8-14.

Google Scholar

[5] A.V. Filippov, Constructing a model of the equivalent wedge oblique cutting edge. Applied Mechanics and Materials. 379 (2013) 139-144.

DOI: 10.4028/www.scientific.net/amm.379.139

Google Scholar

[6] А.А. Bakanov, Calculation of cutting force in drilling with indexable insert drills. Fundamental Researches. 6 (2006) 49p.

Google Scholar

[7] A.V. Filippov, Cut-Layer Cross Section in Oblique Turning. Russian Engineering Research. 34, 11 (2014) 718-721.

DOI: 10.3103/s1068798x14110070

Google Scholar