Temperature-Reduction Value of Conductor with Large Aluminum-Steel Section Ratio Based on Creep Test

Yuan Gao; Yi Qi

doi:10.4028/www.scientific.net/AMR.1051.902

Paper Titles

Experiments of Electronic Water Cooling System on Different Inlet Type and with/without Vortex Fin inside
p.881

Nonlinear Finite Element Static and Corrosion Sensitive Analysis of Radial Steel Gate
p.886

Mixing Two Fluids of Different Densities in a Solar Storage Tank by Lattice Boltzmann Method
p.891

Evaluation of P-T Limit Curves According to Alternative Fracture Toughness Requirements
p.896

Temperature-Reduction Value of Conductor with Large Aluminum-Steel Section Ratio Based on Creep Test
p.902

Experimental Investigation on Damping Characteristics in Pump-Sand Box-Isolation System
p.906

A Measurement Based on Tunable Diode Laser Absorption Spectroscopy for Pressure in Gas Flow
p.910

A Study on Imbalanced Sound Sensitivity of BA Earphones Inducing Deafness
p.915

Experimental and Simulation Research on Flow Characteristics of SCR System in a 100MW Power Station
p.920

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 1051Temperature-Reduction Value of Conductor with...

Temperature-Reduction Value of Conductor with Large Aluminum-Steel Section Ratio Based on Creep Test

Abstract:

Through experimental study on creep characteristics of conductors with large aluminum-steel section ratio, the creep characteristic curve of conductors with aluminum-steel section ratio between 11.34 and 14.47 are obtained. It is recommended that the conductor should have a temperature-reduction value of 25°C according to the conductor temperature-reduction value analyzed by amount of creep, which can be used for reference during line design and construction.

You might also be interested in these eBooks

Applied Engineering Decisions in the Context of Sustainable Development

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 1051)

Pages:

902-905

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.1051.902

Citation:

Cite this paper

Online since:

October 2014

Authors:

Yuan Gao*, Yi Qi

Keywords:

Characteristic Curve, Creep Rate, Large Aluminum-Steel Section Ratio, Temperature-Reduction Value

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] Zhang Diansheng, Design Manual of High-voltage Transmission Line for Electrical Engineering, third ed., Macmillan, Beijing, (2007).

Google Scholar

[2] Li Bozhi, Treatment of Plastic Creep Elongation of Overhead Line, Electric Power Construction, 22(2001)20-26.

Google Scholar

[3] Shao Tianxiao, Mechanical Calculation of Overhead Transmission Line, second ed., Macmillan, Beijing, (2003).

Google Scholar

[4] Wang Xufeng, Li Guangzhe and Wei Jingli, Quantitative Analysis on Plastic Creep Elongation of Conductor/The Fifth International Conference of Power Transmission and Distribution, Beijing, (2005).

Google Scholar

[5] Li Bozhi, Correction of Construction Temperature Caused by Plastic Creep Elongation of Steel-cored Aluminum Wire, Electric Power Technology, 20(1987)20-24.

Google Scholar

[6] Nie Guoyi, Estimation of Plastic Creep Elongation of Steel-cored Aluminum Wire and Treatment of Initial elongation, Electric Power Construction, 11(1990)15-18.

Google Scholar

[7] GB/T 22077-2008, Overhead Electrical Conductors-Creep Test Procedures, Beijing, (2008).

Google Scholar

[8] Xie Guangwei, Mu Pingan et al, Automatic Test Technique of Overhead Conductor Creep, Foreign Electronic Measurement Technology, 25(2006)19-22.

Google Scholar

[9] Xiaodao Che, Wang Weixing, Conductor Elongation Characteristic and Applications of Overhead Transmission Line, Electric Power Construction, 10(1989) 59-65.

Google Scholar