For Libraries For Publication Open Access Downloads About Us Contact Us
Paper Titles
Development of 590MPa Grade Hot-Dip Galvannealed DP Steels
p.83
Effect of Annealing Temperature on Microstructure and Damping Capacity of Twin Roll Cast ZK60 Alloy
p.87
Effect of Ca and Nd Alloying on the Microstructure of Mg-6Al-Ca-Nd Alloy
p.91
Effect of Cu on the Electrochemical Corrosion Behavior of Sn-8Zn-3Bi Lead-Free Solder Alloy
p.95
Effect of Electropulsing Rolling on the Microstructure and Properties of Industrial Pure Titanium TA1
p.99
Effect of Er on Microstructure and Hardness of Al-Zn-In Alloy
p.103
Effect of Grain Size on Microstructure and Orientation of Fe-25Mn-3Si-3Al Steel
p.107
Effect of Nd on Primary Silicon and Mechanical Properties of Hypereutectic Al-17.5%Si Alloy
p.111
Experiment and Analyses on 16 Mn Steel under Cyclic Loading Controlled by Strain
p.115

Effect of Electropulsing Rolling on the Microstructure and Properties of Industrial Pure Titanium TA1

Article Preview

Abstract:

The microstructure and properties of industrial pure titanium TA1 produced by warm rolling and electropulsing rolling were studied and compared in this paper. The results show that both elongation and strength improve after warm rolling, and the elongation of electropulsing rolled TA1 improves significantly and the strength reduces compared to warm rolled TA1. The microstructure after warm rolling shows elongated grains with high density of dislocation. However, after electropulsing rolling, microstructure is much finer, shows some fine grains and sub-grains with lower density of dislocations. The pole figure results show that sharp {0002} basal texture form in electropulsing rolled TA1, and the maximum texture component deviate from{0002} basal texture in warm rolled TA1.

You might also be interested in these eBooks
Advances in Materials and Materials Processing V View Preview

Info:

Periodical:

Advanced Materials Research (Volume 1095)

Pages:

99-102

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.1095.99

Citation:

Cite this paper

Online since:

March 2015

Authors:

Xing Zhou An, Chun Xu, Yan Hui Guo

Keywords:

Electropulsing Rolling, Plasticity, TA1

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

© 2015 Trans Tech Publications Ltd. All Rights Reserved

Share:

Citation:

References

[1] G.G. Purcek, I. Yapici, H.J. Karaman: Mater. Sci. Eng., Vol528 (2011), p.2303.

Google Scholar

[2] H. M. Liao, G.Y. Tang, Y.B. Jiang, Qing Xu, Shiding Sun, Jianan Liu: Mater. Sci. Eng., Vol 529 (2011), p.138.

Google Scholar

[3] A. Sprecher, S. Mannan, H. Conrad: Acta. Mater., Vol 34 (1986), p.1145.

Google Scholar

[4] H. Conrad, N. Karam, S. Mannan: Scripta Metal, Vol17(1983), p.411.

Google Scholar

[5] H. Song, Z. J. Wang: Mater. Sci. tech., Vol 21(2013), p.118.

Google Scholar

[6] S.Q. Tian, Z.H. Xu, G.Y. Tang: Trans. Mater. Heat. Treat., Vol 27(2006), p.103. In Chinese.

Google Scholar

[7] H.Y. Tian, G.Y. Tang, F. Ding: Nonferrous Metals, Vol 59(2007), p.10.

Google Scholar

[8] G.Y. Tang, Y.B. Jiang, J.Q. Cui: Metallurgica equipment, Vol 3(2008), p.63. In Chinese.

Google Scholar

[9] F.Y. Yan, W. Huang, Q.Y. Yang, C.D. Cheng: Forging & stamping technology, Vol 35(2010), p.39. In Chinese.

Google Scholar

[10] Q. Xu , L. Guan, Y. Jiang, G. Tang, S. Wang: Mater. Lett., Vol 64(2010), p.1085.

Google Scholar

[11] Y.H. Zhu, W.B. Lee, X.M. Liu, Y.B. Jiang, G.Y. Tang: Mater. Sci. Eng A , Vol 501( 2009), p.125.

Google Scholar

[12] G.Y. Tang, J. Zhang, M. Zheng, W. Fang, Q. Li: Mater. Sci. Eng A, Vol 281( 2000), p.263.

Google Scholar

© 2025 Trans Tech Publications Ltd. All rights are reserved, including those for text and data mining, AI training, and similar technologies. For open access content, terms of the Creative Commons licensing CC-BY are applied.
Scientific.Net is a registered trademark of Trans Tech Publications Ltd.