Use of Separated Dust from the Formatting and Grinding Cement-Bonded Chipboards to Modify their Composition

Tomáš Melichar; Dalibor Konečný; Jiří Bydžovský; Miroslav Vacula

doi:10.4028/www.scientific.net/AMR.1122.225

Paper Titles

The Thermographic Measuring of the Surface Temperature of the Peripheral Wall after Removing a Technical Device for Elimination of Reflected Radiation
p.205

Thermally-Technical Comparing of Traditional Double Timber Window and Eurowindow
p.210

Thermotechnical Calculation of Air Cavities by Rehabilitation of Wet Brickworks
p.214

Use of Glassy Slag from Biomass Combustion in the Building Industry – Coarse Aggregate
p.219

Use of Separated Dust from the Formatting and Grinding Cement-Bonded Chipboards to Modify their Composition
p.225

Utilization of Liquefying Additives in Clay Fly Ash Grouting Mixtures
p.229

Verification of Applicability of Alternate Sources of Heat for Determination of the Surface Temperature and Emissivity of Glossy Materials
p.233

Verification of Applicability of Thermographical Measuring of the Surface Temperature and the Influence of Emissivity of Glossy Materials while Eliminating the Reflected Radiation Using a Metal Shield
p.237

Comparison of Two Medieval Trusses from the Viewpoint of Geometric and Static Analysis
p.243

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 1122Use of Separated Dust from the Formatting and...

Use of Separated Dust from the Formatting and Grinding Cement-Bonded Chipboards to Modify their Composition

Abstract:

The article presents results of the research focused on suitability assessment of separated dust from formatting and grinding of cement-bonded chipboards to modify their composition. The attention was paid to dust treatment, i.e. milling and sorting. The dust was applied to chipboards in amounts of 5 and 10%. Formulas with water-cement ratio 0.60 and 0.65 were prepared. The influence of sorted dust was subsequently evaluated using setting of selected material properties. In particular the bending strength and tensile strength perpendicular to plate plane were monitored including the influence of frost on these characteristics.

You might also be interested in these eBooks

Proceedings of the Conference on the Rehabilitation and Reconstruction of Buildings (CRRB 2014)

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 1122)

Pages:

225-228

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.1122.225

Citation:

Cite this paper

Online since:

August 2015

Authors:

Tomáš Melichar*, Dalibor Konečný, Jiří Bydžovský, Miroslav Vacula

Keywords:

Alternative Raw Material, Board, Cement, Chip, Dust, Selection, Trimming

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

* - Corresponding Author

References

[1] Khorami, M., Ganjian, E. The effect of limestone powder, silica fume and fibre content on flexural behaviour of cement composite reinforced by waste Kraft pulp. Construction and Building Materials, Elsevier, (2013).

DOI: 10.1016/j.conbuildmat.2013.03.099

Google Scholar

[2] Fan, M., Ndikontar, M., Zhou, X., Ngamveng, J. Cement-bonded composites made from tropical woods: Compatibility of wood and cement. Construction and Building Materials. Elsevier, (2012).

DOI: 10.1016/j.conbuildmat.2012.04.089

Google Scholar

[3] Černý, V., Keprdová, Š. Usability of fly ashes from Czech Republic for sintered artificial aggregate. Advanced Materials Research. 2014. 2014(887-888). pp.805-808. ISSN 1022-6680.

DOI: 10.4028/www.scientific.net/amr.887-888.805

Google Scholar

[4] ČSN EN 310 Wood based panels. Determination of modulus of elasticity in bending and of bending strength. ČNI, (1995).

DOI: 10.3403/00299457

Google Scholar

[5] ČSN EN 319 Particleboards and fibreboards. Determination of transverse tensile strength perpendicular to the plane of the board. ČNI, (1994).

DOI: 10.3403/00299524

Google Scholar

[6] ČSN EN 1328 Cement bonded particleboards - Determination of frost resistance. ČNI, (1998).

Google Scholar