Microstructure Development of Twin Roll Cast AZ31 Sheet in the Pre-Deformation Deep Drawing Process

Pei Wei Bao; Shu Ming Xing; Zhi Min Liu

doi:10.4028/www.scientific.net/AMR.299-300.215

Paper Titles

Study on Microstructure and Mechanical Properties of Hot Rolled Steel Plate Strengthened Complexly by Titanium and Molybdenum
p.197

Post-Process of Density Streaks Image of Flow Field in Supersonic Jet Device Captured by Laser Dual Hologram Interferometry
p.202

Effect of Mineral Mixture of Steel Slag and Blast Furnace Slag on the Properties of Cement
p.206

Anticorrosion Conversion Coating Content Lanthanum and Phosphate on Foam Mg Alloy
p.211

Microstructure Development of Twin Roll Cast AZ31 Sheet in the Pre-Deformation Deep Drawing Process
p.215

Al-0.90%Fe Alloy Sectional Solidified in a Gradient Magnetic Field
p.220

Experimental Confirmation of Ni₅Al₃Phase in Ni-Al Binary System by Diffusion Couple Technique
p.224

Simulation of Grain Growing Process of Zinc-Aluminium Alloy under High Pressure
p.228

Influences of Acting Parameters of Electric Pulse Modification on the Al-22%Si-1.5%Cu Alloy
p.233

HomeAdvanced Materials ResearchAdvanced Materials Research Vols. 299-300Microstructure Development of Twin Roll Cast AZ31...

Microstructure Development of Twin Roll Cast AZ31 Sheet in the Pre-Deformation Deep Drawing Process

Abstract:

Warm deep drawing processing was used to improve the deep drawability of Twin Roll Cast AZ31B magnesium sheet. Conspicuous effects were obtained and the Limited Drawing Ratio value of the sheet was improved by about 50% after the pre-deformation. Influence factor on the drawability of Twin Roll Cast magnesium alloy sheet was also analyzed. Numerical simulation method and microstructure analysis method were used to discuss the mechanisms of formation and develop of Twin Roll Cast microstructure in the twin roll cast process and the pre-deformation process.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Advanced Materials Research (Volumes 299-300)

Pages:

215-219

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.299-300.215

Citation:

Cite this paper

Online since:

July 2011

Authors:

Pei Wei Bao, Shu Ming Xing, Zhi Min Liu

Keywords:

Deep Drawing, Magnesium Alloy, Pre-Deformation, Sheet, Twin Roll Casting (TRC)

Export:

RIS, BibTeX

Price:

Permissions CCC:

Request Permissions

Permissions PLS:

Request Permissions

Сopyright:

Citation:

References

[1] Yang Y. B., Wang F.C., Tan C. W, Wu Y.Y. and Cai H. N.: Transactions of Nonferrous Metals Society of China. Vol. 18(2008), p.1043.

Google Scholar

[2] Hou L.F., Wei Y.H., Liu B.S. and Xu B. S. : Transactions of Nonferrous Metals Society of China, Vol. 18(2008), p.1053.

Google Scholar

[3] Yang L.F., MORI K. and TSU H.: Transactions of Nonferrous Metals Society of China Vol. 18(2008), p.86.

Google Scholar

[4] Wang G.S., Di H.S., Huang F.: Forging ＆ Stamping Technology. Vol. 34 (2009), p.52.

Google Scholar

[5] Zhao H, Li P.J. And He L.J.: The Chinese Journal of Nonferrous Metal. Vo1. 19 (2009), p.1887.

Google Scholar

[6] Hui X.D., Cheng G. L. : Block Amorphous alloy (Chemical Industry Press, China 2007).

Google Scholar

[7] C.A. Schuh, T.C. Hufnagel, U. Ramamurty. Mechanical behavior of amorphous alloys. Acta Materialia Vol. 55(2007), p.4067.

DOI: 10.1016/j.actamat.2007.01.052

Google Scholar

[8] Zeng W.D., Zhou Y.G., Zhou J.: Rare Metal Materials and Engineering. Vol. 35(2006), p.673.

Google Scholar

[9] Shanghai Jiaotong University: Metallographic analysis. (National Defense Industry Press, China 1982).

Google Scholar

[10] Hu H.: Solidification of Metal. (Metallurgical Industry Press, China 1985 ).

Google Scholar

[11] Peng W.P., Peng C.H., Li P. J and Zeng P. : The Chinese Journal of Nonferrous Metals. Vol. 16(2006), p.1724.

Google Scholar

[12] A. Galiyev, R. Kaibyshev, G. Gottstein.: Acta Mater. Vol. 49(2001), p.1199.

Google Scholar